Railgun

For railroad artillery, see Railway gun. For other uses, see Rail-gun.

Basics

In its simplest (and most commonly used) form, the railgun differs from a traditional electric motor ^[5] in that no use is made of additional field windings (or permanent magnets). This basic configuration is formed by a single loop of current and thus requires high currents (e.g., of order one million amperes) to produce sufficient accelerations (and muzzle velocities). A relatively common variant of this configuration is the augmented railgun in which the driving current is channelled through additional pairs of parallel conductors, arranged to increase ("augment") the magnetic field experienced by the moving armature.^[6] These arrangements reduce the current required for a given acceleration. In electric motor terminology, augmented railguns are usually series-wound configurations.

The armature may be an integral part of the projectile, but it may also be configured to accelerate a separate, electrically isolated or non-conducting projectile. Solid, metallic sliding conductors are often the preferred form of railgun armature but "plasma" or "hybrid" armatures can also be used.^[7] A plasma armature is formed by an arc of ionised gas that is used to push a solid, non-conducting payload in a similar manner to the propellant gas pressure in a conventional gun. A hybrid armature uses a pair of "plasma" contacts to interface a metallic armature to the gun rails. Solid armatures may also "transition" into hybrid armatures, typically after a particular velocity threshold is exceeded.

A railgun requires a pulsed DC power supply.^[8] For potential military applications, railguns are usually of interest because they can achieve much greater muzzle velocities than guns powered by conventional chemical propellants. Increased muzzle velocities can convey the benefits of increased firing ranges while, in terms of target effects, increased terminal velocities can allow the use of kinetic energy rounds as replacements for explosive shells. Therefore, typical military railgun designs aim for muzzle velocities in the range of 2000–3500 m/s with muzzle energies of 5–50 MJ. For comparison, 50MJ is equivalent to the kinetic energy of a school bus weighing 5 metric tons, travelling at 509 km/h (316 mph).^[9] For single loop railguns, these mission requirements require launch currents of a few million amperes, so a typical railgun power supply might be designed to deliver a launch current of 5 MA for a few milliseconds. As the magnetic field strengths required for such launches will typically be approximately 10 tesla, most contemporary railgun designs are effectively "air-cored", i.e., they do not use ferromagnetic materials such as iron to enhance the magnetic flux. However, if the barrel is magnetic, i.e., produces a magnetic field perpendicular to the current flow, the force is augmented.

It may be noted that railgun velocities generally fall within the range of those achievable by two-stage light-gas guns; however, the latter are generally only considered to be suitable for laboratory use while railguns are judged to offer some potential prospects for development as military weapons. Another light gas gun, the Combustion Light Gas Gun in a 155 mm prototype form was projected to achieve 2500 m/s with a .70 caliber barrel. In some hypervelocity research projects, projectiles are "pre-injected" into railguns, to avoid the need for a standing start, and both two-stage light-gas guns and conventional powder guns have been used for this role. In principle, if railgun power supply technology can be developed to provide compact, reliable and lightweight units, then the total system volume and mass needed to accommodate such a power supply and its primary fuel can become less than the required total volume and mass for a mission equivalent quantity of conventional propellants and explosive ammunition. Such a development would then convey a further military advantage in that the elimination of explosives from any military weapons platform will decrease its vulnerability to enemy fire.

History

German railgun diagrams

In 1918, French inventor Louis Octave Fauchon-Villeplee invented an electric cannon which is an early form of railgun. He filed for a US patent on 1 April 1919, which was issued in July 1922 as patent no. 1,421,435 "Electric Apparatus for Propelling Projectiles".^[10] In his device, two parallel busbars are connected by the wings of a projectile, and the whole apparatus surrounded by a magnetic field. By passing current through busbars and projectile, a force is induced which propels the projectile along the bus-bars and into flight.^[11]

In 1944, during World War II, Joachim Hänsler of Germany's Ordnance Office proposed the first theoretically viable railgun.^[12] By late 1944, the theory behind his electric anti-aircraft gun had been worked out sufficiently to allow the Luftwaffe's Flak Command to issue a specification, which demanded a muzzle velocity of 2,000 m/s (6,600 ft/s) and a projectile containing 0.5 kg (1.1 lb) of explosive. The guns were to be mounted in batteries of six firing twelve rounds per minute, and it was to fit existing 12.8 cm FlaK 40 mounts. It was never built. When details were discovered after the war it aroused much interest and a more detailed study was done, culminating with a 1947 report which concluded that it was theoretically feasible, but that each gun would need enough power to illuminate half of Chicago.^[11]

During 1950, Sir Mark Oliphant, an Australian physicist and first director of the Research School of Physical Sciences at the new Australian National University, initiated the design and construction of the world's largest (500 megajoule) homopolar generator.^[13] This machine was operational from 1962 and was later used to power a large-scale railgun that was used as a scientific experiment.^[14]

Late into the first decade of the 2000s, the U.S. Navy tested a railgun that accelerates a 3.2 kg (7 pound) projectile to hypersonic velocities of approximately 2.4 kilometres per second (8,600 km/h), about Mach 7.^[15] They gave the project the motto "Velocitas Eradico", Latin for "I, [who am] speed, eradicate"—or in the vernacular, "Speed Kills".

Design

Theory

A railgun consists of two parallel metal rails (hence the name) connected to an electrical power supply. When a conductive projectile is inserted between the rails (at the end connected to the power supply), it completes the circuit. Electrons flow from the negative terminal of the power supply up the negative rail, across the projectile, and down the positive rail, back to the power supply.^[16]

This current makes the railgun behave as an electromagnet, creating a magnetic field inside the loop formed by the length of the rails up to the position of the armature. In accordance with the right-hand rule, the magnetic field circulates around each conductor. Since the current is in the opposite direction along each rail, the net magnetic field between the rails (B) is directed at right angles to the plane formed by the central axes of the rails and the armature. In combination with the current (I) in the armature, this produces a Lorentz force which accelerates the projectile along the rails, away from the power supply. There are also Lorentz forces acting on the rails and attempting to push them apart, but since the rails are mounted firmly, they cannot move.

By definition, if a current of one ampere flows in a pair of infinitely long parallel conductors that are separated by a distance of one metre, then the magnitude of the force on each metre of those conductors will be exactly 0.2 micro-newtons. Furthermore, in general, the force will be proportional to the square of the magnitude of the current and inversely proportional to the distance between the conductors. It also follows that, for railguns with projectile masses of a few kg and barrel lengths of a few m, very large currents will be required to accelerate projectiles to velocities of the order of 1000 m/s.

A very large power supply, providing on the order of one million amperes of current, will create a tremendous force on the projectile, accelerating it to a speed of many kilometres per second (km/s). Twenty km/s has been achieved with small projectiles explosively injected into the railgun. Although these speeds are possible, the heat generated from the propulsion of the object is enough to erode the rails rapidly. Under high-use conditions, current railguns would require frequent replacement of the rails, or to use a heat-resistant material that would be conductive enough to produce the same effect. At this time it is generally acknowledged that it will take major breakthroughs in material science and related disciplines to produce high-powered railguns capable of firing more than a few shots from a single set of rails. The barrel must withstand these conditions for up to several rounds per minute for thousands of shots without failure or significant degradation. These parameters are well beyond the state of the art in materials science.^[17]

Mathematical formula

If a railgun could be designed to provide a uniform magnetic field of strength $B$ , oriented at right angles to both the armature and the bore axis, then, with an armature current $I$ and an armature length ${\boldsymbol {\ell }}$ , the force $F$ accelerating the projectile would be given by the well known formula:

F=BI{\boldsymbol {\ell }}

In practice, the force must be calculated after making due allowances for the spatial variation of the magnetic field over the volume of the armature. For example, the magnitude of the force vector can be determined from a form of the Biot–Savart law and a result of the Lorentz force. It can be derived mathematically in terms of the permeability constant ( $\mu_0$ ), the radius of the rails (which are assumed to be circular in cross section) ( $r$ ), the distance between the central axes of the rails ( $d$ ) and the current ( $I$ ) as follows:

It can be shown from the Biot-Savart law that at one end of a semi-infinite current-carrying wire, the magnetic field at a given perpendicular distance ( $s$ ) from the end of the wire is given by:^[18]

\mathbf {B} (s)={\frac {\mu _{0}I}{4\pi s}}{\hat {\phi }}

Note this is if the wire runs from the location of the armature e.g. from x = 0 back to $x=-\infty$ and $s$ is measured relative to the axis of the wire.

So, if the armature connects the ends of two such semi-infinite wires separated by a distance, $d$ , a fairly good approximation assuming the length of the wires is much larger than $d$ , the total field from both wires at any point on the armature, or any point in the plane between the two wires is:

\mathbf {B} (s)={\frac {\mu _{0}I}{4\pi }}\left({\frac {1}{s}}+{\frac {1}{d-s}}\right){\hat {z}}

Where $s$ is the perpendicular distance from the point on the armature to the axis of one of the wires.

Note that ${\hat {\phi }}$ between the rails is ${\hat {z}}$ assuming the rails are lying in the xy plane and run from x = 0 back to $x=-\infty$ as suggested above.

To obtain an approximate expression for the force on the railgun armature, we start by again assuming that the railgun rails can be modeled as a pair of semi-infinite conductors. This allows us to use the above expression for the magnetic field on the armature in the Lorentz Force Law,

\mathbf {F} =I\int \mathrm {d} {\boldsymbol {\ell }}\times \mathbf {B}

Inserting the expression for the magnetic field into the Lorentz force law and setting the bounds of integration to $r$ and $d-r$ , assuming the armature is a bar between and perpendicular to the rails making $\mathrm {d} {\boldsymbol {\ell }}$ point in the ${\hat {y}}$ , we find the force on the armature is

\mathbf {F} =I\int _{r}^{d-r}\mathrm {d} {\boldsymbol {\ell }}\times {\frac {\mu _{0}I}{4\pi }}\left({\frac {1}{s}}+{\frac {1}{d-s}}\right){\hat {z}}={\frac {\mu _{0}I^{2}}{2\pi }}\ln {\left({\frac {d-r}{r}}\right)}{\hat {x}}

The formula is based on the assumption that the distance ( $l$ ) between the point where the force ( $F$ ) is measured and the beginning of the rails is greater than the separation of the rails ( $d$ ) by a factor of about 3 or 4 ( $l>3d$ ). Some other simplifying assumptions have also been made; to describe the force more accurately, the geometry of the rails and the projectile must be considered.

With most practical railgun geometries, it is not easy to produce an electromagnetic expression for the railgun force that is both simple and reasonably accurate. Instead, most practical railgun analyses actually used a lumped circuit model to describe the relationship between the driving current and the railgun force. In these models the voltage across the railgun breech is given by:

V=IR+{\frac {{\text{d}}(LI)}{{\text{d}}t}}

Then the barrel resistance and inductance are assumed to vary linearly with the projectile position, so that

R=R'x

L=L'x

from which

V=I(R'x+L'v)+L'x{\frac {{\text{d}}I}{{\text{d}}t}}

If the driving current is held constant, there is a power flow equal to $I^{2}L'v$ which represents the electromagnetic work done. In this simple model, exactly half of this is assumed to be needed to establish the magnetic field along the barrel, i.e., as the length of the current loop increases. The other half represents the power flow into the kinetic energy of the projectile. Since power can be expressed as force times speed, this gives the standard result that the force on the railgun armature is given by:

$F={\frac {L'I^{2}}{2}}$

This simple equation shows that high accelerations will require very high currents. For an ideal square bore railgun, the value of $L'$ would be about 0.6 microHenries per metre ( $\mu$ .H/m) but most practical railgun barrels exhibit lower values of $L'$ than this.

Since the lumped circuit model describes the railgun force in terms of fairly normal circuit equations, it becomes possible to specify a simple time domain model of a railgun.

Ignoring friction and air drag, the projectile acceleration is given by:

{\frac {{\text{d}}v}{{\text{d}}t}}={\frac {L'I^{2}}{2m}}

where m is the projectile mass. The motion along the barrel is given by:

{\frac {{\text{d}}x}{{\text{d}}t}}=v

and the above voltage and current terms can be placed into appropriate circuit equations to determine the time variation of current and voltage.

It can also be noted that the textbook formula for the high frequency inductance per unit length of a pair of parallel round wires, of radius r and axial separation d is:

L'={\frac {\mu _{0}}{\pi }}\ln {\left({\frac {d-r}{r}}\right)}

so the lumped parameter model also predicts the force for this case as:

$F={\frac {L'I^{2}}{2}}={\frac {\mu _{0}I^{2}}{2\pi }}\ln {\left({\frac {d-r}{r}}\right)}$ .

With practical railgun geometries, much more accurate two or three dimensional models of the rail and armature current distributions (and the associated forces) can be computed, e.g., by using finite element methods to solve formulations based on either the scalar magnetic potential or the magnetic vector potential.

Design considerations

The power supply must be able to deliver large currents, sustained and controlled over a useful amount of time. The most important gauge of power supply effectiveness is the energy it can deliver. As of December 2010, the greatest known energy used to propel a projectile from a railgun was 33 megajoules.^[19] The most common forms of power supplies used in railguns are capacitors and compulsators which are slowly charged from other continuous energy sources.

The rails need to withstand enormous repulsive forces during shooting, and these forces will tend to push them apart and away from the projectile. As rail/projectile clearances increase, arcing develops, which causes rapid vaporization and extensive damage to the rail surfaces and the insulator surfaces. This limited some early research railguns to one shot per service interval.

The inductance and resistance of the rails and power supply limit the efficiency of a railgun design. Currently different rail shapes and railgun configurations are being tested, most notably by the United States Navy, the Institute for Advanced Technology at the University of Texas at Austin, and BAE Systems.

Materials used

The rails and projectiles must be built from strong conductive materials; the rails need to survive the violence of an accelerating projectile, and heating due to the large currents and friction involved. Some erroneous work has suggested that the recoil force in railguns can be redirected or eliminated; careful theoretical and experimental analysis reveals that the recoil force acts on the breech closure just as in a chemical firearm.^[20]^[21]^[22]^[23] The rails also repel themselves via a sideways force caused by the rails being pushed by the magnetic field, just as the projectile is. The rails need to survive this without bending and must be very securely mounted. Currently published material suggests that major advances in material science must be made before rails can be developed that allow railguns to fire more than a few full-power shots before replacement of the rails is required.

Heat dissipation

In current designs massive amounts of heat are created by the electricity flowing through the rails, as well as by the friction of the projectile leaving the device. The heat created by this friction itself can cause thermal expansion of the rails and projectile, further increasing the frictional heat. This causes three main problems: melting of equipment, decreased safety of personnel, and detection by enemy forces due to increased infrared signature. As briefly discussed above, the stresses involved in firing this sort of device require an extremely heat-resistant material. Otherwise the rails, barrel, and all equipment attached would melt or be irreparably damaged.

In practice, the rails used with most railgun designs are subject to erosion from each launch. Additionally, projectiles can be subject to some degree of ablation, and this can limit railgun life, in some cases severely.^[24]

Applications

Railguns have a number of potential practical applications, primarily for the military. However, there are other theoretical applications currently being researched.

Launch or launch assist of spacecraft

Main article: Mass driver

Weaponry

Drawings of electric gun projectiles

Railguns are being researched as weapons with projectiles that do not contain explosives or propellants, but are given extremely high velocities: 2,500 m/s (8,200 ft/s) (approximately Mach 7 at sea level) or more. For comparison, the M16 rifle has a muzzle speed of 930 m/s (3,050 ft/s), and the 16"/50 caliber Mark 7 gun that armed World War II American battleships has a muzzle speed of 760 m/s (2,490 ft/s)), which because of its much greater mass generated a muzzle energy of 360 MJ and a downrange kinetic impact of energy of over 160 MJ. By firing smaller projectiles at extremely high velocities, railguns can yield kinetic energy impacts equal or superior to the destructive energy of 5" Naval guns, but with much greater range. This decreases ammunition size and weight, allowing more ammunition to be carried and eliminating the hazards of carrying explosives or propellants in a tank or naval weapons platform. Also, by firing at greater velocities, railguns have greater range, less time to target, and at shorter ranges less wind drift, bypassing the physical limitations of conventional firearms: "the limits of gas expansion prohibit launching an unassisted projectile to velocities greater than about 1.5 km/s and ranges of more than 50 miles [80 km] from a practical conventional gun system."^[30] Current railgun technologies necessitate a long and heavy barrel, but a railgun's ballistics far outperform conventional cannons of equal barrel lengths. Railguns can also deliver area of effect damage by detonating a bursting charge in the projectile which unleashes a swarm of smaller projectiles over a large area.^[31]^[32]

Assuming that the many technical challenges facing fieldable railguns are overcome, including issues like railgun projectile guidance and rail endurance, the increased launch velocities of railguns will provide advantages over more conventional guns for a variety of offensive and defensive scenarios. Railguns have the potential to be used against both surface and airborne targets.

The first weaponized railgun planned for production, the General Atomics Blitzer system, began full system testing in September 2010. The weapon launches a streamlined discarding sabot round designed by Boeing's Phantom Works at 1,600 m/s (5,200 ft/s) (approximately Mach 5) with accelerations exceeding 60,000 g_n.^[33] During one of the tests, the projectile was able to travel an additional 7 kilometres (4.3 mi) downrange after penetrating a ¹⁄₈ inch (3.2 mm) thick steel plate. The company hopes to have an integrated demo of the system by 2016 followed by production by 2019, pending funding. Thus far, the project is self-funded.^[34]

In October 2013, General Atomics unveiled a land based version of the Blitzer railgun. A company official claimed the gun could be ready for production in "two to three years".^[35]

Railguns are being examined for use as anti-aircraft weapons to intercept air threats, particularly anti-ship cruise missiles, in addition to land bombardment. A supersonic sea-skimming anti-ship missile can appear over the horizon 20 miles from a warship, leaving a very short reaction time for a ship to intercept it. Even if conventional defense systems react fast enough, they are expensive and only a limited number of large interceptors can be carried. A railgun projectile can reach several times the speed of sound faster than a missile; because of this, it can hit a target, such as a cruise missile, much faster and farther away from the ship. Projectiles are also typically much cheaper and smaller, allowing for many more to be carried (they have no guidance systems, and rely on the railgun to supply their kinetic energy, rather than providing it themselves). The speed, cost, and numerical advantages of railgun systems may allow them to replace several different systems in the current layered defense approach.^[36] A railgun projectile without the ability to change course can hit fast-moving missiles at a maximum range of 30 nmi (35 mi; 56 km).^[37] As is the case with the Phalanx CIWS, unguided railgun rounds will require multiple/many shots to bring down maneuvering supersonic anti-ship missiles, with the odds of hitting the missile improving dramatically the closer it gets. The Navy plans for railguns to be able to intercept endoatmospheric ballistic missiles, stealthy air threats, supersonic missiles, and swarming surface threats; a prototype system for supporting interception tasks is to be ready by 2018, and operational by 2025. This timeframe suggests the weapons are planned to be installed on the Navy's next-generation surface combatants, expected to start construction by 2028.^[38]

Helical railgun

Helical railguns are multi-turn railguns that reduce rail and brush current by a factor equal to the number of turns. Two rails are surrounded by a helical barrel and the projectile or re-usable carrier is also helical. The projectile is energized continuously by two brushes sliding along the rails, and two or more additional brushes on the projectile serve to energize and commute several windings of the helical barrel direction in front of and/or behind the projectile. The helical railgun is a cross between a railgun and a coilgun. They do not currently exist in a practical, usable form.

A helical railgun was built at MIT in 1980 and was powered by several banks of, for the time, large capacitors (approximately 4 farads). It was about 3 meters long, consisting of 2 meters of accelerating coil and 1 meter of decelerating coil. It was able to launch a glider or projectile about 500 meters.

Plasma railgun

A plasma railgun is a linear accelerator and a plasma energy weapon which, like a projectile railgun, uses two long parallel electrodes to accelerate a "sliding short" armature. However, in a plasma railgun, the armature and ejected projectile consists of plasma, or hot, ionized, gas-like particles, instead of a solid slug of material. MARAUDER (Magnetically Accelerated Ring to Achieve Ultra-high Directed Energy and Radiation) is, or was, a United States Air Force Research Laboratory project concerning the development of a coaxial plasma railgun. It is one of several United States Government efforts to develop plasma-based projectiles.^[39] The first computer simulations occurred in 1990, and its first published experiment appeared on August 1, 1993.^[40]^[41] As of 1993 the project appeared to be in the early experimental stages. The weapon was able to produce doughnut-shaped rings of plasma and balls of lightning that exploded with devastating effects when hitting their target.^[42] The project's initial success led to it becoming classified, and only a few references to MARAUDER appeared after 1993. The project may or may not have been scrapped some time after 1995.

Tests

Diagram showing the cross-section of a linear motor cannon

Full-scale models have been built and fired, including a 90 mm (3.5 in) bore, 9 MJ kinetic energy gun developed by the US DARPA. Rail and insulator wear problems still need to be solved before railguns can start to replace conventional weapons. Probably the oldest consistently successful system was built by the UK's Defence Research Agency at Dundrennan Range in Kirkcudbright, Scotland. This system was established in 1993 and has been operated for over 10 years. Using its associated flight range for internal, intermediate, external and terminal ballistics, it achieved several mass and velocity records.

The Yugoslavian Military Technology Institute developed, within a project named EDO-0, a railgun with 7 kJ kinetic energy, in 1985. In 1987 a successor was created, project EDO-1, that used projectile with a mass of 0.7 kg (1.5 lb) and achieved speeds of 3,000 m/s (9,800 ft/s), and with a mass of 1.1 kg (2.4 lb) reached speeds of 2,400 m/s (7,900 ft/s). It used a track length of 0.7 m (2.3 ft). According to those working on it, with other modifications it was able to achieve a speed of 4,500 m/s (14,800 ft/s). The aim was to achieve projectile speed of 7,000 m/s (23,000 ft/s). At the time, it was considered a military secret.

China is now one of the major players in electromagnetic launchers; in 2012 it hosted the 16th International Symposium on Electromagnetic Launch Technology (EML 2012) at Beijing.^[43] Satellite imagery in late 2010 suggested that tests were being conducted at an armor and artillery range near Baotou, in the Inner Mongolia Autonomous Region.^[44]

U.S. military tests

The United States military is funding railgun experiments. At the University of Texas at Austin Center for Electromechanics, military railguns capable of delivering tungsten armor-piercing bullets with kinetic energies of nine megajoules have been developed.^[45] 9 MJ is enough energy to deliver 2 kg (4.4 lb) of projectile at 3 km/s (1.9 mi/s)—at that velocity a rod of tungsten or another dense metal could easily penetrate a tank, and potentially pass through it.

U.S. Navy tests

The United States Naval Surface Warfare Center Dahlgren Division demonstrated an 8 MJ railgun firing 3.2 kg (7.1 lb) projectiles in October 2006 as a prototype of a 64 MJ weapon to be deployed aboard Navy warships. The main problem the U.S. Navy has had with implementing a railgun cannon system is that the guns wear out due to the immense pressures, stresses and heat that are generated by the millions of amperes of current necessary to fire projectiles with megajoules of energy. Such weapons, while not nearly as powerful as a cruise missile like a BGM-109 Tomahawk cruise missile that will deliver 3000 MJ of destructive energy to a target, will theoretically allow the Navy to deliver more granular firepower at a fraction of the cost of a missile, and will be much harder to shoot down versus future defensive systems. For context another relevant comparison is the Rheinmetall 120mm gun used on main battle tanks will generate 9 MJ of muzzle energy. An MK 8 round fired from the 16" guns of an Iowa Class battleship at 2500 fps (762 m/s) has 360 MJ of kinetic energy at the muzzle.

Since then, BAE Systems has delivered a 32 MJ prototype (muzzle energy) to the U.S. Navy.^[46] The same amount of energy is released by the detonation of 4.8 kg (11 lb) of C4.

On January 31, 2008, the U.S. Navy tested a railgun that fired a projectile at 10.64 MJ with a muzzle velocity of 2,520 m/s (8,270 ft/s).^[47] The power was provided by a new 9-megajoule prototype capacitor bank using solid-state switches and high-energy-density capacitors delivered in 2007 and an older 32-MJ pulse power system from the US Army’s Green Farm Electric Gun Research and Development Facility developed in the late 1980s that was previously refurbished by General Atomics Electromagnetic Systems (EMS) Division.^[48] It is expected to be ready between 2020 and 2025.^[49]

A test of a railgun took place on December 10, 2010, by the US Navy at the Naval Surface Warfare Center Dahlgren Division.^[50] During the test, the Office of Naval Research set a world record by conducting a 33 MJ shot from the railgun, which was built by BAE Systems.^[19]^[51]

A test took place in February, 2012, at the Naval Surface Warfare Center Dahlgren Division. While similar in energy to the aforementioned test, the railgun used is considerably more compact, with a more conventional looking barrel. A General Atomics-built prototype was delivered for testing in October 2012.^[52]

External video
Additional footage
February 2012 test

The U.S. Navy plans to integrate a railgun that has a range of over 160 km (100 mi) onto a ship by 2016.^[53] This weapon, while having a form factor more typical of a naval gun, will utilize components largely in common with those developed and demonstrated at Dahlgren.^[54] The hyper-velocity rounds weigh 10 kg (23 lb), are 18 in (460 mm), and are fired at Mach 7.^[55]

A future goal is to develop projectiles that are self-guided - a necessary requirement to hit distant targets or intercepting missiles.^[56] When the guided rounds are developed, the Navy is projecting each round to cost about $25,000,^[57] though it must be noted that developing guided projectiles for guns has a history of doubling or tripling initial cost estimates. Some high velocity projectiles developed by the Navy have command guidance, but the accuracy of the command guidance is not known, nor even if it can survive a full power shot.

Currently, the only US Navy ships that can produce enough electrical power to get desired performance are the Zumwalt-class destroyers; they can generate 78 megawatts of power, more than is necessary to power a railgun. Engineers are working to derive technologies developed for the DDG-1000 series ships into a battery system so other warships can operate a railgun.^[58] Most current destroyers can spare only nine megawatts of additional electricity, while it would require 25 megawatts to propel a projectile to the desired maximum range ^[59] (i.e., to launch 32MJ projectiles at a rate of 10 shots per minute). Even if current ships, such as the Arleigh Burke-class destroyer, can be upgraded with enough electrical power to operate a railgun, the space taken up on the ships by the integration of an additional weapon system may force the removal of existing weapon systems to make room available.^[60] The first shipboard tests will be from a railgun installed on an Expeditionary Fast Transport. Though ships of that class are non-combatants, they were chosen for their available cargo and topside space and schedule flexibility. They will not be permanently installed on the EFT, and the Navy has yet to decide which ship classes will receive a fully operational railgun.^[61] Single shot tests will be held in 2016, followed by an autoloader in 2018.^[62] According to the Navy, "current research is focused on a rep-rate capability of multiple rounds per minute which entails development of a tactical prototype gun barrel and pulsed power systems incorporating advanced cooling techniques. Components are designed to transition directly into prototype systems now being conceptualized."^[54] So as of March 2014 multiple rep railgun were in the conceptual stage and have a ways to go before reaching the prototype stage.

Though the 23 lb projectiles have no explosives, their Mach 7 velocity gives them 32 megajoules of energy, but impact kinetic energy downrange will typically be 50 percent or less of the muzzle energy. The Navy is looking into other uses for railguns, besides land bombardment, such as air defense; with the right targeting systems, projectiles could intercept aircraft, cruise missiles, and even ballistic missiles. The Navy is also developing directed energy weapons for air defense use, but it will be years before they will be effective.

The railgun will be part of a Navy fleet that envisions future offensive and defensive capabilities being provided in layers: lasers to provide close range defense, railguns to provide medium range attack and defense, and cruise missiles to provide long-range attack; though railguns will cover targets up to 100 miles away that previously needed a missile.^[63]

The Navy may eventually enhance railgun technology to enable it to fire at a range of 200 nmi (230 mi; 370 km) and impact with 64 megajoules of energy. One shot would require 6 million amps of current, so it will take a long time to develop capacitors that can generate enough energy and strong enough gun materials.^[44]

Outstanding issues in fielding railgun weapons

Major technological and operational hurdles must be overcome before railguns can be deployed:

Railgun durability: To date railgun demonstrations, while impressive, have not demonstrated an ability to fire multiple full power shots from the same set of rails. The Navy has claimed hundreds of shots from the same set of rails. In a March 2014 statement to the Intelligence, Emerging Threats and Capabilities Subcommittee of the House Armed Services Committee, Chief of Naval Research Admiral Matthew Klunder stated, "Barrel life has increased from tens of shots to over 400, with a program path to achieve 1000 shots."^[54] However, the Office of Naval Research (ONR) will not confirm that the 400 shots are full-power shots. Further there is nothing published to indicate there are any high megajoule class railguns with the capability of firing hundreds of full-power shots while staying within the strict operational parameters necessary to fire railgun shots accurately and safely. According to an article by Globalsecurity.org:^[64] railguns should be able to fire 6 rounds per minute with a rail life of about 3000 rounds. Tolerating launch accelerations of tens of thousands of g's, extreme pressures and megaampere currents over this sort of duty cycle is currently beyond the state of the art.
Projectile guidance: A future capability critical to fielding a real railgun weapon is developing a robust guidance package that will allow the railgun to fire at distant targets or to hit incoming missiles. Developing such a package is a real challenge. The Navy's RFP Navy SBIR 2012.1 - Topic N121-102^[65] for developing such a package gives a good overview of just how challenging railgun projectile guidance is:

The package must fit within the mass (< 2 kg), diameter (< 40 mm outer diameter), and volume (200 cm³) constraints of the projectile and do so without altering the center of gravity. It should also be able to survive accelerations of at least 20,000 g (threshold) / 40,000 g (objective) in all axes, high electromagnetic fields (E > 5,000 V/m, B > 2 T), and surface temperatures of > 800 deg C. The package should be able to operate in the presence of any plasma that may form in the bore or at the muzzle exit and must also be radiation hardened due to exo-atmospheric flight. Total power consumption must be less than 8 watts (threshold)/5 watts (objective) and the battery life must be at least 5 minutes (from initial launch) to enable operation during the entire engagement. In order to be affordable, the production cost per projectile must be as low as possible, with a goal of less than $1,000 per unit.

On June 22, 2015, General Atomics’ Electromagnetic Systems announced that projectiles with on-board electronics survived the whole railgun launch environment and performed their intended functions in four consecutive tests on June 9 and 10 June at the U.S. Army’s Dugway Proving Ground in Utah. The on-board electronics successfully measured in-bore accelerations and projectile dynamics, for several kilometers downrange, with the integral data link continuing to operate after the projectiles impacted the desert floor, which is essential for precision guidance.^[66]

Trigger for inertial confinement fusion

Railguns may also be miniaturized for inertial confinement nuclear fusion.

Fusion is triggered by very high temperature and pressure at the core.
- Current technology calls for multiple lasers, usually over 100, to concurrently strike a fuel pellet, creating a symmetrical compressive pressure.
- Railguns may be able to trigger fusion by firing energetic plasma from multiple directions. The process developed involves four key steps.^[67]
  - Plasma is pumped into a chamber.
  - When the pressure is great enough, a diaphragm will rupture, sending gas down the rail.
  - Shortly afterwards, a sufficient voltage is applied to the rails, creating a conduction path of ionized gas.
  - This plasma is accelerated down the rail, eventually being ejected at a large velocity.
The rails and dimensions are on the order of centimetres.

References

↑ Fletcher, Seth (2013-06-05). "Navy Tests 32-Megajoule Railgun |". Popular Science. Retrieved 2013-06-16.
↑ Rashleigh, C. S. & Marshall, R. A. (April 1978). "Electromagnetic Acceleration of Macroparticles to High Velocities". J. Appl. Phys. 49 (4): 2540. doi:10.1063/1.325107.
↑ "Rail Strike". The Economist. 2015-05-09. Retrieved 2016-01-31.
↑ Atkinson, Nancy (2010-09-14). "NASA Considering Rail Gun Launch System to the Stars". Universe Today.
↑ Hindmarsh, John (1977). Electrical Machines and their Applications. Oxford: Pergamon Press. p. 20. ISBN 0-08-021165-8.
↑ Fiske, D.; Ciesar, J.A.; Wehrli, H.A.; Riemersma, H.; et al. (January 1991). "The HART 1 Augmented Electric Gun Facility". IEEE Transactions on Magnetics. 27 (1): 176–180. doi:10.1109/20.101019. ISSN 0018-9464.
↑ Batteh, Jad. H. (January 1991). "Review of Armature Research". IEEE Transactions on Magnetics. IEEE Magnetics Society. 27 (1): 224–227. doi:10.1109/20.101030.
↑ Gully, John (January 1991). "Power Supply Technology for Electric Guns". IEEE Transactions on Magnetics. IEEE Magnetics Society. 27 (1): 329–334. doi:10.1109/20.101051.
↑ "50 megajoules kinetic energy". Wolfram Alpha. 2014-04-28.
↑ Fauchon-Villeplee, André Louis Octave (1922). "US Patent 1,421,435 "Electric Apparatus for Propelling Projectiles"".
1 2 Hogg, Ian V. (1969). The Guns: 1939/45. London: Macdonald. ISBN 9780019067102. OCLC 778837078.
↑ "Archived copy" (PDF). Archived from the original (PDF) on 2016-03-04. Retrieved 2015-08-22.
↑ Ophel, Trevor & Jenkin, John (1996). "Chapter 2:The Big Machine" (PDF). Fire in the Belly: The first fifty years of the pioneer School at the ANU. Australian National University. ISBN 9780858000483. OCLC 38406540. Retrieved 2014-04-10.
↑ Barber, J. P. (March 1972). The Acceleration of Macroparticles and a Hypervelocity Electromagnetic Accelerator (Ph.D thesis). Australian National University. OCLC 220999609.
↑ Borrell, Brendan (2008-02-06). "Electromagnetic Railgun Blasts Off". MIT Technology Review.
↑ Harris, William (11 October 2005). "How Rail Guns Work". HowStuffWorks. Retrieved 2011-03-25.
↑ "Electromagnetic Rail Gun (EMRG)". GlobalSecurity.org.
↑ Smolinski, Jason. "Magnetism". Retrieved 2014-09-04.
1 2 Ackerman, Spencer (2010-12-10). "Video: Navy's Mach 8 Railgun Obliterates Record". Wired.
↑ Weldon, Wm. F.; Driga, M. D. & Woodson, H. H. (November 1986). "Recoil in electromagnetic railguns". IEEE Transactions on Magnetics. 22 (6): 1808–1811. doi:10.1109/TMAG.1986.1064733. ISSN 0018-9464.
↑ Cavalleri, G.; Tonni, E. & Spavieri, G. (May 2001). "Reply to "Electrodynamic force law controversy"". Physical Review E. 63 (5): 058602. Bibcode:2001PhRvE..63e8602C. doi:10.1103/PhysRevE.63.058602.
↑ Kathe, Eric L. (November 2000). Recoil Considerations for Railguns: Technical Report ARCCB-TR-00016 (pdf). U.S. Army ARDEC Benet Laboratories.
↑ Putnam, Michael J. (December 2009). An Experimental Study of Electromagnetic Lorentz Force and Rail Recoil (M.Sc. thesis). Naval Postgraduate School.
↑ Barros, Sam (2010-11-11). "PowerLabs Rail Gun!". Powerlabs.org (Blog). Retrieved 2014-04-10.
↑ Uranga, Alejandra; Kirk, Daniel R.; Gutierrez, Hector; Meinke, Rainer B.; et al. (2005). Rocket Performance Analysis Using Electrodynamic Launch Assist (PDF). Proceedings of the 43rd AIAA Aerospace Sciences Meeting and Exhibit (10–13 January 2005). Reno, Nevada.
↑ Advanced Magnet Lab, Inc. (2008) "Space and Defense" magnetlab.com Archived October 14, 2008, at the Wayback Machine.
↑ Advanced Magnet Lab, Inc. (2008) "Direct Double-Helix" magnetlab.com Archived February 13, 2011, at the Wayback Machine.
1 2 3 McNab, I.R. (January 2003). "Launch to space with an electromagnetic railgun" (PDF). IEEE Transactions on Magnetics. 35 (1): 295–304. doi:10.1109/TMAG.2002.805923. ISSN 0018-9464.
↑ Proton is estimated at $5000/kg as of 2015.
↑ Adams, David Allan (February 2003). "Naval Rail Guns Are Revolutionary" (PDF). U.S. Naval Institute Proceedings. 129 (2): 34. Archived from the original (PDF) on 2007-07-08.
↑ "Railguns". http://navy-matters.blogspot.com/. Navy Matters. Retrieved 11 February 2015. External link in |website= (help)
↑ Fredenburg, Michael. "Railguns: The Next Big Pentagon Boondoggle?". www.nationalreview.com. National Review.
↑ Fallon, Jonathon (2012-04-25). "General Atomics' Railgun Travels 4 Miles, Even After Blasting Through a Steel Plate [Video]". CubicleBot. Retrieved 2012-04-25.
↑ "Blitzer Railgun". General Atomics. 2012-04-25. Retrieved 2012-04-25.
↑ Fisher Jr, Richard D. (2013-10-22). "AUSA 2013: General Atomics unveils Blitzer land-based railgun". Jane's. Archived from the original on 2014-03-29. Retrieved 2014-12-22.
↑ Page, Lewis (2010-12-25). "'Blitzer' railgun already 'tactically relevant', boasts maker". The Register.
↑ Freedberg Jr., Sydney J. (2014-11-21). "47 Seconds From Hell: A Challenge To Navy Doctrine". Breaking Defense.
↑ LaGrone, Sam (2015-01-05). "Navy Wants Rail Guns to Fight Ballistic and Supersonic Missiles Says RFI". USNI News.
↑ Plasma railgun#Examples
↑ Sovinec, C. R. (1990). "Phase 1b MARAUDER computer simulations". IEEE international conference on plasma science. 22 (16).
↑ Dengan, et. al, J. H. (1993-08-01). "Compact toroid formation, compression, and acceleration". Physics of Fluids B. doi:10.1063/1.860681.
↑ "Unfriendly Fire". Archived from the original on February 23, 2007.
↑ LIST OF PAPERS, 16th International Symposium on Electromagnetic Launch Technology (EML 2012) Beijing, China, ISBN 978-1-4673-0306-4, http://toc.proceedings.com/16118webtoc.pdf
1 2 Five Futuristic Weapons That Could Change Warfare - Nationalinterest.org, 1 November 2014
↑ "EM Systems". University of Texas. Archived from the original on 2007-10-10.
↑ Sofge, Erik (2007-11-14). "World's Most Powerful Rail Gun Delivered to Navy". Popular Mechanics. Retrieved 2007-11-15.
↑ "U.S. Navy Demonstrates World's Most Powerful EMRG at 10 MJ". United States Navy. 2008-02-01.
↑ "General Atomics Team Powers Navy Rail Gun to New World Record, accessed 14 Oct 2009"
↑ "The Navy shows off its insane magnetic railgun of the future". Dvice.com. 2008-02-02. Retrieved 2014-04-10.
↑ Fein, Geoff. "Navy Sets New World Record with Electromagnetic Railgun Demonstration". http://www.navy.mil/. United States Navy. Retrieved 13 February 2015. External link in |website= (help)
↑ LaGrone, Sam (2010-12-15). "Electromagnetic railgun sets new world record". Jane's. Archived from the original on 2010-12-17. Retrieved 2014-12-22.
↑ "Navy Evaluating Second Electromagnetic Railgun Innovative Naval Prototype". Office of Naval Research. 2012-10-09. Retrieved 2012-10-20.
↑ Osborn, Kris (2014-01-10). "Future Destroyers Likely to Fire Lasers, Rail Guns". Military.com.
1 2 3 Klunder, Matthew. "Statement of Read Admiral Matthew L. Klunder, United States Navy Chief of Naval Research Before the Intelligence, Emerging Threats and Capabilities Subcommittee of the House Armed Services Committee on the Fiscal Year 2015 Budget Request" (PDF). www.acq.osd.mil. House Armed Services Committee. Retrieved 13 February 2015.
↑ McDuffee, Allen (2014-04-09). "Navy's New Railgun Can Hurl a Shell Over 5,000 MPH". Wired.
↑ Osborn, Kris (2014-01-16). "Navy Rail Gun Showing Promise". Defensetech.org.
↑ Irwin, Sandra. "Naval Guns: Can They Deliver 'Affordable' Precision Strike?". www.nationaldefensemagazine.com. National Defense Magazine. Retrieved 11 February 2015.
↑ Sharp, David (2014-02-18). "US Navy Ready to Deploy Laser for 1st Time". Military.com.
↑ Atherton, Kelsey D. (2014-04-08). "The Navy Wants To Fire Its Ridiculously Strong Railgun From The Ocean". Popular Science.
↑ LaGrone, Sam (2013-06-07). "NAVSEA on Flight III Arleigh Burkes". USNI News.
↑ "Navy to deploy electromagnetic railgun". Military1.com. 2014-04-07.
↑ Bacon, Lance M. (2014-04-12). "Railgun tests from ship set for '16". Military Times. Gannett Government Media. Archived from the original on 2014-04-14. Retrieved 2014-12-22.
↑ Freedberg Jr., Sydney J. (2014-04-07). "Navy's Magnetic Super Gun To Make Mach 7 Shots At Sea In 2016: Adm. Greenert". Breakingdefense.com.
↑ "Electromagnetic Rail Gun EMRG". Globalsecurity.org. Retrieved 10 February 2015.
↑ Frost, Tracy. "Survivable Electronics for Control of Hypersonic Projectiles under Extreme Acceleration". United States Navy SBIR/STTR Program. Retrieved 10 February 2015.
↑ Archived June 26, 2015, at the Wayback Machine.
↑ Witherspoon, F.D.; Bomgardner, R.; Case, A.; Messer, S.; et al. (2009). MiniRailgun accelerator for plasma linear driven HEDP and magneto-inertial fusion experiments (PDF). 36th IEEE International Conference on Plasma Science. San Diego, CA.
↑ Sam LaGrone (2015-04-14). "NAVSEA Details At Sea 2016 Railgun Test on JHSV Trenton - USNI News". News.usni.org. Retrieved 2015-12-24.

External links

Wikimedia Commons has media related to Railgun.

Look up railgun in Wiktionary, the free dictionary.

NRL Railgun Demonstration Video US Naval Research Laboratory, July 2010
USN sets five-year target to develop electromagnetic gun at the Wayback Machine (archived November 22, 2009) Jane's Defence Weekly, 20 July 2006
Electromagnetic Railgun Popular Science article, June 2004
Video of Navy railgun test firing, Navy Electromagnetic Launch Facility, Test Shot #1, 2 October 2006. Source: Fredericksburg.com, accessed 30 January 2007
World’s Most Powerful Rail Gun Delivered to Navy, 14 November 2007

Non-rocket spacelaunch

Spaceflight

Static structures

Compressive

Tensile

Orbiting skyhooks	Skyhook Momentum exchange tether

Space elevators	Space elevator

Dynamic structures

Projectile launchers

Electrical	Coilgun Mass driver Railgun StarTram

Chemical	Space gun Blast wave accelerator Ram accelerator

Mechanical	Slingatron

Reaction drives

Buoyant lifting

See also: Rocket sled launch
Megascale engineering

Category

Emerging technologies

Fields

Displays

Next generation	FED FLCD iMoD Laser LPD OLED OLET QD-LED SED TPD TDEL TMOS

Screenless	Bionic contact lens Head-mounted display Head-up display Optical head-mounted display Virtual retinal display

Other	Autostereoscopy Flexible display Holographic display Computer-generated holography Multi-primary color display Ultra HD Volumetric display

Electronics

Energy

Production	Airborne wind turbine Artificial photosynthesis Biofuels Carbon-neutral fuel Concentrated solar power Fusion power Home fuel cell Hydrogen economy Methanol economy Molten salt reactor Nantenna Photovoltaic pavement Space-based solar power Vortex engine

Storage	Beltway battery Compressed air energy storage Flywheel energy storage Grid energy storage Lithium–air battery Molten salt battery Nanowire battery Research in lithium-ion batteries Silicon–air battery Thermal energy storage Ultracapacitor

Other	Smart grid Wireless power

IT and
communications

Manufacturing

Launch	Fusion rocket Non-rocket spacelaunch Mass driver Orbital ring Space elevator Space fountain Space tether Reusable launch system

Propulsion	Beam-powered propulsion Ion thruster Laser propulsion Plasma propulsion engine Helicon thruster VASIMR Project Orion Nuclear pulse propulsion Solar sail

Other	Interstellar travel Propellant depot

Transport

Aerial	Adaptive compliant wing Aeroscraft Backpack helicopter Delivery drone Flying car High-altitude platform Jet pack Pulse detonation engine Scramjet Spaceplane Skylon Supersonic transport

Land	Airless tire Tweel Alternative fuel vehicle Hydrogen vehicle Driverless car Ground effect train Maglev train Personal rapid transit Vactrain ET3 Global Alliance Hyperloop Vehicular communication systems

Pipeline	Pneumatic transport Automated vacuum collection Foodtubes

Other

Topics

Category
List

This article is issued from Wikipedia - version of the 12/2/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.