Research in lithium-ion batteries

Research in lithium-ion batteries has produced many proposed refinements of lithium-ion batteries. Ideas used have focused on improving energy density, safety, charge time, cycle durability, flexibility, and cost. As of 2014 few of these innovations had appeared in commercial products.

Anode

Anodes have traditionally been made of graphite.

Titanium dioxide with aluminum

In 2015, researchers at Massachusetts Institute of Technology developed a quick charge battery that has four times the energy density of typical lithium-ion batteries. The battery uses tiny capsules of titanium dioxide filled with aluminium. The aluminium yolk has space to expand and contract inside the shell. This overcomes previous problems of using aluminium as a battery anode.[1]

Titanium dioxide

In 2014, researchers at Nanyang Technological University used titanium dioxide in an anode and achieved 10,000 charging cycles. The battery can be charged to 70% in two minutes. They used a gel material made from titanium dioxide, an abundant, cheap and safe material found in soil. They developed a simple method to turn naturally spherical titanium dioxide particles into nanotubes. This nanostructure sped up the charging reaction.[2]

Lithium

Lithium anodes have been used for the first lithium-ion batteries in the previous century, based on the TiS
2/Li cell chemistry, but were eventually abandoned due to dendrite formation, causing internal short-circuits and fire hazard.[3][4] In 2014, researchers at Stanford University discovered that a pure-lithium anode increased energy density 400%. Researchers claimed that the anode did not expand during charging. This is done by building nanospheres, which are protective layers of interconnected carbon domes on top of the anode.[5]

Also in 2014, a second technique was announced by Cornell University researchers that added halogenated lithium salts to the liquid electrolyte. This prevented the formation of battery-destroying metal dendrites as the battery went through charge/discharge cycles.[6]

Carbon

Carbon black

In 2014, researchers at Oak Ridge National Laboratory developed an anode from modified carbon black from discarded tires. The new technology is environmentally friendly. It also has a higher energy density.[7]

Nanotube

In 2014, researchers at University of California, Riverside developed a battery that charges up to 16 times faster with 60% additional energy density. They use a three-dimensional, cone-shaped cluster of carbon nanotubes.[8]

That same year, researchers at Northwestern University found that metallic single-walled carbon nanotubes (SWCNTs) accommodate lithium much more efficiently than their semiconducting counterparts. If made denser, semiconducting SWCNT films take up lithium at levels comparable to metallic SWCNTs.[9]

In 2015, researchers examined the feasibility of using carbon nanotubes decorated with mesoporous cobalt oxide (CNT@CO3O4) as electrodes in a lithium-ion battery. They expected the porous structure of the cobalt oxide to enhance diffusion of the electrolyte into the electrode. Researchers synthesized the CNT@CO3O4 and confirmed the composition using Raman spectroscopy. They then performed electrochemical measurements using Swagelok-type cells, taking voltammetry measurements over numerous cycles. They found that the CNT@CO3O4 achieved theoretical capacity up to the second cycle, but decayed with successive cycles. While the material needs to be optimized, it demonstrates high electrochemical activity and a possible electrode material option for the future. These findings are significant because the same measurements can be performed on other metal oxides, offering a wider range of materials to use in lithium-ion batteries. [10]

Microsheets

Heating polystyrene packing peanuts to between 500 and 900 °C (932 to 1,652 °F) in an inert atmosphere, in either the presence or absence of a transition metal salt catalyst produced either nanoparticles or microsheets that made excellent anodes. The sheets were about one tenth the thickness of graphite anodes, reducing charging times and exhibiting less electrical resistance. Specific capacity reached 420 mAh/g, vs the theoretical 372 mAh/g maximum for graphite. The anodes survived 300 charging cycles without a significant capacity loss. The microsheets' porous structure exposed more contact area between the anode and the liquid electrolyte.[11]

In 2015 researchers announced a one-step process for using natural silk to create 4.7% nitrogen-doped carbon-based nanosheets that reversibly 1865 mA h/g over 10,000 cycles with only a 9 percent capacity loss. The surface area was SBET: 2494 m2/g, hierarchical pore volume was 2.28 cm3/g. Capacitance reached 242 F/g and energy density was 102 W h/kg (48 W h/L).[12]

Graphene nanofoam

In 2015 hydrogen-treated graphene nanofoam electrodes in LIBs showed higher capacity and faster transport. Chemical synthesis methods used in standard anode manufacture leave significant amounts of atomic hydrogen. Experiments and multiscale calculations revealed that low-temperature hydrogen treatment of defect-rich graphene can improve rate capacity. The hydrogen interacts with the graphene defects to open gaps to facilitate lithium penetration, improving transport. Additional reversible capacity is provided by enhanced lithium binding near edges, where hydrogen is most likely to bind.[13] Rate capacities increased by 17-43% at 200 mA/g.[14]

Porous Graphene

In 2015, researchers in China used porous graphene as the material for a lithium ion battery anode in order to increase the specific capacity and binding energy between lithium atoms at the anode. The properties of the battery can be tuned by applying strain. The binding energy increases as biaxial strain is applied.[15]

Pollen

In 2016 researchers pyrolized bee and cattail pollen to produce materials for an anode. Pyrolysis in an argon container produced pure carbon. The resulting carbon particles were heated at a lower temperature of around 300 °C (572 °F) in the presence of oxygen, which created pores in the carbon, increasing its energy capacity. In prototype devices at temperatures of 25 and 50 °C (77 and 122 °F) achieved gravimetric capacity of 590 mAh/g at 50 °C and 382 mAh/g at 25 °C.[16]

Silicon

Silicon is an earth abundant element, and is fairly inexpensive to refine to high purity. When alloyed with lithium it has a theoretical capacity of ~3,600 milliampere hours per gram (mAh/g), which is nearly 10 times the energy density of graphite electrodes (372 mAh/g).[17] One of silicon's inherent traits, unlike carbon, is the expansion of the lattice structure by as much as 400% upon full lithiation (charging). For bulk electrodes, this causes great structural stress gradients within the expanding material, inevitably leading to fractures and mechanical failure, which significantly limits the lifetime of the silicon anodes.[18][19] In 2011, a group of researchers assembled data tables that summarized the morphology, composition, and method of preparation of those nanoscale and nanostructured silicon anodes, along with their electrochemical performance. [20] Below are various structural morphologies attempted to overcome issue with silicon's intrinsic properties.

Carbon cage

In 2016 researchers announced a method for caging 3 nm-diameter silicon particles in a shell of graphene. The particles were first coated with nickel. Graphene layers then coated the metal. Acid dissolved the nickel, leaving enough of a void within the cage for the silicon to expand. The particles broke into smaller pieces, but remained functional within the cages. The cages also prevented the silicon from reacting with the electrolyte.[21][22]

In 2014 researchers encapsulated silicon nanoparticles inside carbon shells, and then encapsulated clusters of the shells with more carbon. The shells provide enough room inside to allow the nanoparticles to swell and shrink without damaging the shells, improving durability.[23]

Flash heat treatment

In 2015 researchers announced a flash heat treatment for fabricating silicon anodes that minimizes volume expansion while boosting the performance and cycle capability of lithium-ion batteries. The material delivered 1,000 mAh/ g for 2,275 cycles at 2 A/g with increased energy capacity, by minimizing volume expansion.[24][25]

Nanowire

Main article: Nanowire battery

In 2012 researchers announced a prototype using silicon nanowires to improve cycle life.[26][27] Silicon nanowires can expand/contract without breaking. However, they are costly to make.[28]

Silicon/carbon composite

In 2014, Energ2 created a battery that blends silicon with carbon, claiming to increase energy density and offer five times greater cycle durability.[29]

Nanofiber

In 2015 a prototype electrode was demonstrated that consists of sponge-like silicon nanofibers increases Columbic efficiency and avoids the physical damage from silicon's expansion/contractions. The nanofibers were created by applying a high voltage between a rotating drum and a nozzle emitting a solution of tetraethyl orthosilicate (TEOS). The material was then exposed to magnesium vapors. The nanofibers contain 10 nm diameter nanopores on their surface. Along with additional gaps in the fiber network, these allow for silicon to expand without damaging the cell. Three other factors reduce expansion: a 1 nm shell of silicon dioxide; a second carbon coating that creates a buffer layer; and the 8-25 nm fiber size, which is below the size at which silicon tends to fracture.[30]

Conventional lithium-ion cells use binders to hold together the active material and keep it in contact with the current collectors. These inactive materials make the battery bigger and heavier. Experimental binderless batteries do not scale because their active materials can be produced only in small quantities. The prototype has no need for current collectors, polymer binders or conductive powder additives. Silicon comprises over 80 percent of the electrode by weight. The electrode delivered 802 mAh/g after more than 600 cycles, with a Coulombic efficiency of 99.9 percent.[30]

Nanoparticle

In 2014, researchers developed a silicon anode with an energy density above 1,100 mAh/g and a durability of 600 cycles, making their anode nearly three times more powerful and longer lasting than a typical commercial anode. They used porous silicon particles using ball-milling and stain-etching.[17]

In 2013, researchers developed a battery with three times the energy density of a conventional li-ion, and can be recharged in less time. It utilizes anodes made from porous silicon nanoparticles.[31][32]

Sand

In 2014, researchers at University of California, Riverside announced an anode made from high-quartz sand collected from Cedar Creek Reservoir in Texas. They milled the sand to the nanometer scale and purified it, producing a similar color and texture to powdered sugar. Grinding salt and magnesium into the purified quartz and heating removed oxygen from the quartz, resulting in pure silicon with a porous, sponge-like consistency. After an extensive low current density activation process, at a discharge rate at C/2 tested over 1000 cycles, the half cell demonstrated a reversible capacity of 1024 mAh/g and a Coulombic efficiency of 99.1% using a lithium metal counter electrode.[33]

Mesoporous sponge

In 2014, researchers at Pacific Northwest National Laboratory discovered that spongy silicon doubles the energy density of lithium-ion batteries. A mesoporous silicon sponge that is capable of being filled with silicon rather than the silicon expanding. Silicon typically expands to 400% during charging, with the new technology only expanding 30%[34]

Polymer hydrogel

In 2013, researchers at Stanford University developed a battery that maintains high energy density through 5,000 cycles. They used silicon and conducting polymer hydrogel, a spongy substance similar to the material used in soft contact lenses and other household products. This process doesn't cause fires. It is also inexpensive.[35]

Silicon oxide-coated silicon nanotube

In 2012, researchers at Stanford and SLAC developed a battery with superior durability. It maintains 85% of the energy density after 6,000 cycles. They are using a double-walled silicon nanotube coated with a thin layer of silicon oxide. This strong outer layer keeps the outside wall of the nanotube from expanding.[36]

Si/MgO/graphite

In 2011, researchers at State University of New York developed a silicon/magnesium oxide/graphite composite.[37][38]

Clusters

In 2011, researchers from Northwestern University developed a battery that increased cycle durability and energy density by up to a factor of ten. They sandwiched clusters of silicon between graphene sheets. They used a redox process to create in-plane defects (10 to 20 nanometers) in the graphene sheets so the lithium ions would have a "shortcut" into the anode and be stored there by reaction with silicon.[39]

Polymer

In 2011, researchers at United States Department of Energy national laboratories developed a battery anode that can absorb eight times the amount of lithium. The polymer binds closely to silicon particles while they expand and shrink.[40]

Tin

In 2013, researchers at Washington State University developed a tin electrode technology that they predicted would triple the energy density of lithium ion batteries. The technology involves using standard electroplating processes to create tin nanoneedles that do not short circuit when the tin expands by one third during charging.[41][42]

Nanowire

Main article: Nanowire battery

In 2007, researchers at Stanford University invented the nanowire battery, which improved battery performance. It uses nanowires to increase the surface area of one or both electrodes. Both replace the traditional graphite anode. One uses silicon, while the other uses germanium.[43][44][45]

Nickel-fluoride

In 2014, researchers at Rice University announced a method to create a flexible, long-lasting battery. They used nanoporous nickel(II) fluoride electrodes layered around a solid electrolyte without using lithium. The device retained 76% of its energy density after 10,000 charge-discharge cycles and 1,000 bending cycles.[46]

Copper

Nanorods

In 2006, researchers developed a battery using nanotechnology that improves energy density by several times. Active materials are applied in a very thin film to copper nanorods anchored to sheets of copper foil The nanorods supply 50 cm2 of active material per cm2 of substrate.[47]

Copper antimonide

In 2015 researchers announced a solid-state 3-D battery annode made of copper antimonide. It is electroplated onto a copper foam. The anode is then layered with a solid polymer electrolyte that provides a physical barrier across which ions (but not electrons) can travel. The cathode is an inky slurry. The volumetric energy density was up to twice as much energy conventional batteries. The solid electrolyte prevents dendrite formation.[48]

Iron-phosphate

In 2009, researchers at MIT developed a battery using genetically engineered viruses to make a more environmentally friendly battery.[49] In 2015, another MIT group announced a flexible, puncture-resilient battery with fewer, thicker electrodes that used a semisolid aqueous suspension lithium-iorn-phosphate (LFP)/lithium-titanium-phosphate (LTP) to achieve higher energy density than a conventional aqueous vanadium-redox flow battery. Using suspended particles instead of solid slabs greatly reduces the tortuosity (path length of charged particles as they move through the material).[50]

Lithium metal foil

Historically, lithium metal was used only for non-rechargeable cells, because it tends to react with the electrolyte, trapping the lithium ions and preventing more and more of them from participating in future charge/discharge cycles. The reaction also creates dendrites, metal spikes that can cause short circuits and heating that can ignite the flammable electrolyte. Lithium metal remains a subject of interest because of its potential to increased energy density by 2x or more.[51][52]

Liquid/solid electrolyte

In 2015, an MIT spinoff company, SolidEnergy, demonstrated a battery that uses a thin sheet of lithium-metal foil. The company claimed to have solved multiple issues, including safety and lifetime.[52]

SolidEnergy uses a combination of solid and liquid electrolytes. The solid electrolyte is applied to the lithium-metal foil—the ions don’t have far to travel through this thin material, so it does not matter that they move relatively slowly. Once through the solid electrolyte, they reach a non-flammable liquid electrolyte, which ferries them to the opposite electrode. The electrolyte has additives that prevent the lithium metal from reacting with it and that prevent dendrites.[52]

SolidEnergy’s technology does not require new manufacturing equipment and can be recharged 300 times while retaining 80 percent of its storage capacity. It works at room temperature, whereas some other lithium-metal batteries operate at much higher temperatures.[52]

Solid/solid electrolyte

In 2014 Seeo demonstrated a prototype of a solid-state battery, replacing the traditional liquid electrolyte with two polymer layers. One is soft and conducts ions; the other is hard and prevents dendrite formation. Battery charge cycling had yet to be assessed.[53]

Aluminum/titanium

In 2015 an anode made from aluminum/titanium "yolk-and-shell" nanoparticles was introduced. The nanoparticles have a solid titanium outer shell and an inner aluminum "yolk" that can expand and contract within the shell, storing and releasing ions without damaging the structure of the electrode. Like lithium or silicon, aluminum can store much more energy per unit weight than graphite.[54]

Production involved placing 50 nm-diameter aluminum particles in a solution of sulfuric acid and titanium oxysulfate. This coated the nanoparticles in a hard titanium shell three to four nanometers thick. A few hours in the acid shrank the aluminum particles to about 30 nanometers without affecting the outer shell. This gave the aluminum nanoparticles room to expand considerably as they absorbed lithium, without damaging the cell's electric contacts. The anode can reportedly store 1.2 Ah/g at a normal charging rate, declining to 0.66 Ah/g at a higher rate.[54]

Cathode

As of 2016, cathodes are typically made of a material containing lithium.

Vanadium

In 2007, Subaru introduced a battery with double the energy density while only taking 15 minutes for an 80% charge. They used vanadium, which is able to load two to three times more lithium ions onto the cathode.[55]

Cobalt

In 2014, researchers at the School of Engineering at the University of Tokyo and Nippon Shokubai discovered that adding cobalt to the lithium oxide crystal structure gave it seven times the energy density.[56][57]

Graphene/lithium metal

In 2014, researchers at Rensselaer Polytechnic Institute developed an all carbon battery that improves energy density and cycle durability. After over 1,000 charges, the battery showed highly stable performance. The new battery uses an anode and cathode made from graphene with metallic lithium and without cobalt.[58]

Disordered materials

In 2014, researchers at Massachusetts Institute of Technology found that creating lithium-ion batteries with disorder in the materials they are composed of achieved 660 watt-hours per kilogram at 2.5 volts.[59]

In 2015 researchers blended powdered vanadium pentoxide with borate compounds at 900 C and quickly cooled the melt to form glass. The resulting paper-thin sheets were then crushed into a powder to increase their surface area. The powder was coated with reduced graphite oxide (RGO) to increase conductivity while protecting the electrode. The coated powder was used for the battery cathodes. Trials indicated that capacity was quite stable at high discharge rates and remained consistently over 100 charge/discharge cycles. Energy density reached around 1,000 watt-hours per kilogram and a discharge capacity that exceeded 300 mAh/g.[60]

Graphene oxide coated sulfur

In 2014, researchers at USC Viterbi School of Engineering used a graphite oxide coated sulfur cathode to create a battery with 800 mAh/g for 1,000 cycles of charge/discharge, over 5 times the energy density of commercial cathodes. Sulfur is abundant, low cost and has low toxicity. Sulfur has been a promising cathode candidate owing to its high theoretical energy density, over 10 times that of metal oxide or phosphate cathodes. However, sulfur's low cycle durability has prevented its commercialization. Graphene oxide coating over sulfur is claimed to solve the cycle durability problem. Graphene oxide high surface area, chemical stability, mechanical strength and flexibility.[17]

Nanophosphate

In 2012, researchers at A123 developed a battery that operates in extreme temperatures without the need for thermal management material. It went through 2,000 full charge-discharge cycles at 45 C while maintaining over 90% energy density. It does this using a nanophosphate positive electrode.[61][62]

Transition-metal Oxides

In 2000, researchers from the Université de Picardie Jules Verne examined the use of nano-sized transition-metal oxides as cathode materials. The metals used were cobalt, nickel, copper and iron and they proved to have capacities of 700 mA h/g and maintain full capacity for 100 cycles. These promising results show that transition-metal oxides may be useful in ensuring the integrity of the lithium-ion battery over many discharge-recharge cycles. [63]

Seawater

In 2012, researchers at Polyplus Corporation created a battery with an energy density more than triple that of traditional lithium-ion batteries using seawater. It's energy density is 1,300 W·h/kg, which is a lot more than the traditional 400 W·h/kg. It has a solid lithium positive electrode and a solid electrolyte. It could be used in underwater applications.[64]

Purpurin

In 2012, researchers at Rice University, The City College of New York and U.S. Army Research Laboratory found that using purpurin (1,2,4-Trihydroxyanthraquinone) in the cathode is more environmentally friendly than using the traditional lithium cobalt oxide.[65]

Three-dimensional nanostructure

In 2011, researchers at University of Illinois at Urbana-Champaign discovered that wrapping a thin film into a three-dimensional nanostructure can decrease charge time by a factor of 10 to 100. The technology is also capable of delivering a higher voltage output.[66] In 2013, the team improved the microbattery design, delivering 30 times the energy density 1,000x faster charging.[67] The technology also delivers better power density than supercapacitors. The device achieved a power density of 7.4 W/cm2/mm.[68]

Lithium

Lithium nickel manganese cobalt oxide

In 2009, researchers at Nissan announced a lithium nickel manganese cobalt oxide cathode (NMC). The new battery offered twice the energy density.[69]

Lithium iron phosphate

Main article: Nanoball batteries

In 2009, scientists at Massachusetts Institute of Technology created nanoball batteries that increased charge rates 100 times. They are capable of a 10-second re-charge of a cell phone battery and a 5-minute re-charge of an electric car battery. The cathode is composed of nanosized balls of lithium iron phosphate. The rapid charging is because the nanoballs transmit electrons to the surface of the cathode at a much higher rate. The batteries have also shown higher energy density, power density and cycle durability.[70][71]

Lithium manganese silicon oxide

A “lithium orthosilicate-related” cathode compound,  Li
2MnSiO
4, was able to support a charging capacity of 335 mAh/g.[72] Li2MnSiO4@C porous nanoboxes were synthesized via a wet-chemistry solid-state reaction method. The material displayed a hollow nanostructure with a crystalline porous shell composed of phase-pure Li2MnSiO4 nanocrystals. Powder X-ray diffraction patterns and transmission electron microscopy images revealed that the high phase purity and porous nanobox architecture were achieved via monodispersed MnCO3@SiO2 core–shell nanocubes with controlled shell thickness.[73]

Air

Main article: Lithium–air battery

In 2013, researchers at MIT used a genetically modified virus called M13 to create crosslinked manganese oxide nanowire electrodes covered in spikes that more than double the surface area of the electrode along with its energy density. 3-5 weight-percent palladium increases conductivity. This room temperature process is water-based. Specific capacity of 7,340 mAh/ gc+catalyst) of specific energy at 0.4 A/ gc.[74]

In 2009, researchers at the University of Dayton Research Institute announced a solid-state battery with higher energy density that uses air as its cathode. When fully developed, the energy density could exceed 1,000 Wh/kg.[75][76]

Analysis technique

In 2014, researchers at Brookhaven National Laboratory conducted three studies that concluded the usage of nanoscale coatings and other methods could be used to improve the cycle durability of batteries.[77]

In 2014, researchers at Nissan announced a new analytic technique to allow them to observe how cathodes operate.[78]

In 2014, researchers at Helmholtz-Zentrum Berlin found that a lithium-rich cathode material ((x)Li
2MnO
3(1-x)LiMO
2) could be charged and discharged rapidly or at higher currents. In the formula, "M" stands for a transition metal. The material had twice the regular amount of lithium and smaller amounts of rare, toxic elements like nickel and cobalt. The technique allowed them to determine that the battery's rapid energy density drop was due to the rearrangement of oxygen atoms.[79]

In 2014, researchers at Technical University of Munich used a neutron beam to observe when metallic lithium forms during charging without cutting the battery open. Metallic lithium formations lead to a reduced cycle durability and short circuits.[80]

In 2014, researchers at Michigan Technological University discovered atomic shuffling when using transmission electron microscopy. They took a closer look at how the ions move into and out of the anode causing stress.[81]

Electrolyte

Currently, electrolytes are typically made of lithium salts in a liquid organic solvent. Research centers on increased safety via reduced flammability and reducing shorts via preventing dendrites.

Additive

In 2015 researchers announced that a mixture of lithium nitrate and lithium polysulfide formed a solid and stable interface between the electrode and the electrolyte and that it prevented dendrite formation. The prototype device ran with 99 percent efficiency over 300 charging cycles.[82]

Copper

In 2014, researchers at Stanford University discovered that adding a copper nanolayer to the electrolyte can detect fires by responding to a drop in the voltage caused by a dendrite, most likely formed during charging.[83]

Kevlar

In 2015 a battery using a separator membrane made of nanofibers extracted from Kevlar was demonstrated. It prevents dendrite growth because its pores are only 15-20 nm across, smaller than dendrites' 20- to 50-nm nanoscale tips, but large enough to allow individual lithium ions to pass. The membrane can be much thinner than existing separators.[84] Kevlar is an insulator and offers good heat resistance. The university has founded a spin-off company, Elegus Technologies, to further develop and commercialize the technology. Production is expected to begin toward the end of 2016.[85]

Perfluoropolyether

In 2014, researchers at University of North Carolina found a way to replace the electrolyte’s flammable organic solvent with nonflammable perfluoropolyether (PFPE). PFPE is usually used as an industrial lubricant, e.g., to prevent marine life from sticking to the ship bottoms. The material exhibited unprecedented high transference numbers and low electrochemical polarization, indicative of a higher cycle durability.[86]

Sticky

In 2014, researchers at Washington State University developed a chewing gum like substance that may replace liquid electrolytes. This new material contains liquid, but is sticky, which eliminates the fire hazard. This material is flexible, suggesting use in bendable electronics in the future.[87]

Solid-state

While no solid-state batteries have reached the market, multiple groups are researching this alternative. The notion is that solid-state designs are safer because they prevent dendrites from causing short circuits. They may have other benefits ranging from lower temperature operation to increased energy density.

In 2015 researchers announced an electrolyte using superionic lithium-ion conductors, which are compounds of lithium, germanium, phosphorus and sulfur.[88]

Lithium

Salt

In 2015 researchers announced a new electrolyte completely eliminates dendrites and promises to increase battery efficiency and vastly improve current carrying capacity.[89]

The material was 99% efficient and was compatible with a lithium metal anode. The electrolyte used lithium bis(fluorosulfonyl)imide salt, an organosilicon compound added to the solvent dimethoxyethanein. Instead of dendrites, the electrode developed a thin sheet of lithium nodules that did not extend into the electrolyte and risk short-circuiting the battery. The device survived more than 1,000 charge/discharge cycles producing 98.4 percent of its initial charge, with a current of around 4 milliamps per square centimeter.[89]

Thiophosphate

In 2015, researchers worked with a lithium carbon fluoride battery. They incorporated a solid lithium thiophosphate electrolyte wherein the electrolyte and the cathode worked in cooperation, resulting in capacity 26 percent. Under discharge, the electrolyte generates a lithium fluoride salt that further catalyzes the electrochemical activity, converting an inactive component to an active one. More significantly, the technique was expected to substantially increase battery life.[90]

Superhalogen

Conventional electrolytes generally contain halogens, which are toxic. In 2015 researchers claimed that these materials could be replaced with non-toxic superhalogens with no compromise in performance. In superhalogens the vertical electron detachment energies of the moieties that make up the negative ions are larger than those of any halogen atom.[91] The researchers also found that the procedure outlined for Li-ion batteries is equally valid for other metal-ion batteries, such as sodium-ion or magnesium-ion batteries.[92]

Design and management

Charging

In 2014, researchers at MIT, Sandia National Laboratories, Samsung Advanced Institute of Technology America and Lawrence Berkeley National Laboratory discovered that uniform charging could be used with increased charge speed to speed up battery charging. This discovery could also increase cycle durability to ten years. Traditionally slower charging prevented overheating, which shortens cycle durability. The researchers used a particle accelerator to learn that in conventional devices each increment of charge is absorbed by a single or a small number of particles until they are charged, then moves on. By distributing charge/discharge circuitry throughout the electrode, heating and degradation could be reduced while allowing much greater power density.[93][94]

In 2014, researchers at Qnovo developed software for a smartphone and a computer chip capable of speeding up re-charge time by a factor of 3-6, while also increasing cycle durability. The technology is able to understand how the battery needs to be charged most effectively, while avoiding the formation of dendrites.[95]

In 2014, StoreDot announced it had started working on a technology called multifunction electrode (MFE), that will enable future electric vehicles to fully charge in only 5 minutes. The MFE is a combination of a conductive polymer and metal oxide.[96]

Management

Durability

In 2014, independent researchers from Canada announced a battery management system that increased cycles four-fold, that with specific energy of 110 – 175 Wh/kg using a battery pack architecture and controlling algorithm that allows it to fully utilize the active materials in battery cells. The process maintains lithium-ion diffusion at optimal levels and eliminates concentration polarization, thus allowing the ions to be more uniformly attached/detached to the cathode. The SEI layer remains stable, preventing energy density losses.[97][98]

Thermal

In 2016 researchers announced a reversible shutdown system for preventing thermal runaway. The system employed a thermoresponsive polymer switching material. This material consists of electrochemically stable, graphene-coated, spiky nickel nanoparticles in a polymer matrix with a high thermal expansion coefficient. Film electrical conductivity at ambient temperature was up to 50 S cm−1. Conductivity decreases within one second by 107-108 at the transition temperature and spontaneously recovers at room temperature. The system offers 103–104x greater sensitivity than previous devices.[99][100]

Flexibility

In 2014, multiple research teams and vendors demonstrated flexible battery technologies for potential use in textiles and other applications.

One technique made li-ion batteries flexible, bendable, twistable and crunchable using the Miura fold. This discovery uses conventional materials and could be commercialized for foldable smartphones and other applications.[101]

Another approached used carbon nanotube fiber yarns. The 1 mm diameter fibers were claimed to be lightweight enough to create weavable and wearable textile batteries. The yarn was capable of storing nearly 71 mAh/g. Lithium manganate (LMO) particles were deposited on a carbon nanotube (CNT) sheet to create a CNT-LMO composite yarn for the cathode. The anode composite yarns sandwiched a CNT sheet between two silicon-coated CNT sheets. When separately rolled up and then wound together separated by a gel electrolyte the two fibers form a battery. They can also be wound onto a polymer fiber, for adding to an existing textile. When silicon fibers charge and discharge, the silicon expands in volume up to 300 percent, damaging the fiber. The CNT layer between the silion-coated sheet buffered the silicon's volume change and held it in place.[102]

A third approach produced rechargeable batteries that can be printed cheaply on commonly used industrial screen printers. The batteries used a zinc charge carrier with a solid polymer electrolyte that prevents dendrite formation and provides greater stability. The device survived 1,000 bending cycles without damage.[103]

A fourth group created a device that is one hundredth of an inch thick and doubles as a supercapacitor. The technique involved etching a 900 nanometer-thick layer of Nickel(II) fluoride with regularly spaced five nanometer holes to increase capacity. The device used an electrolyte made of potassium hydroxide in polyvinyl alcohol. The device can also be used as a supercapacitor. Rapid charging allows supercapacitor-like rapid discharge, while charging with a lower current rate provides slower discharge. It retained 76 percent of its original capacity after 10,000 charge-discharge cycles and 1,000 bending cycles. Energy density was measured at 384 Wh/kg, and power density at 112 kW/kg.[104]

Volume Expansion

Current research has been primarily focused on finding new materials and characterizing by means of specific capacity (mAh/g), which provides a good metric to compare and contrast all electrode materials. Recently, some of the more promising materials are showing some large volume expansions which need to be considered upon engineering devices. Lesser known to this realm of data is the volumetric capacity (mAh/cm3) of various materials to their design.

Nanotechnology

Researchers have taken various approaches to improving performance and other characteristics by using nanostructured materials. One strategy is to increase electrode surface area. Another is to reduce the distance between electrodes to reduce transport distances. A third is to allow the use of materials that exhibit unacceptable flaws when use in bulk forms, such as silicon.

Finally, adjusting the geometries of the electrodes, e.g., by interdigitating anode and cathode units variously as rows of anodes and cathodes, alternating anodes and cathodes, hexagonally packed 1:2 anodes:cathodes and alternating anodic and cathodic triangular poles. One electrode can be nested within another.

Carbon nanotubes and nanowires have been examined for various purposes, as have aerogels and other novel bulk materials.

Finally, various nanocoatings have been examined, to increase electrode stability and performance.

Nanosensors is now being integrated in to each cell of the battery. This will help to monitor the state of charge in real time which will be helpful not only for security reason but also be useful to maximise the use of the battery. [105]

See also

References

  1. ↑ Charge your smartphone in SIX minutes: 'Yolk and shell' battery technology could end long waits while devices power up, Daily Mail, 11 August 2015, Richard Gray
  2. ↑ Ultra-fast charging batteries that can be 70% recharged in just two minutes, Science Daily, 13 October 2014
  3. ↑ Whittingham, M.Stanley (1978). "Chemistry of intercalation compounds: Metal guests in chalcogenide hosts". Progress in Solid State Chemistry. 12: 41. doi:10.1016/0079-6786(78)90003-1.
  4. ↑ Whittingham, M. S. (1976). "Electrical Energy Storage and Intercalation Chemistry". Science. 192 (4244): 1126–1127. doi:10.1126/science.192.4244.1126. PMID 17748676.
  5. ↑ Battery Life 'Holy Grail' Discovered. Phones May Last 300% Longer, Forbes, 29 July 2014, Gordon Kelly
  6. ↑ Borghino, Dario (August 18, 2014). "Add salt to significantly extend the life of lithium-based batteries". Gizmodo. Retrieved October 12, 2014.
  7. ↑ Recycled Tires Could Power New Lithium-Ion Batteries Science World Report, 28 August 2014, Catherine Griffin
  8. ↑ New li-ion battery anode could charge electronics in minutes, Gizmag, 17 June 2014, Dario Borghino
  9. ↑ Nanotubes make for better lithium-ion batteries, Nanotechweb.org, 3 March 2014
  10. ↑ Wenelska, K. (2015). "Carbon nanotubes decorated by mesoporous cobalt oxide as electrode material for lithium-ion batteries". Chemical Physics Letters. 635: 185–189.
  11. ↑ Coxworth, Ben (March 23, 2015). "Packing peanuts could be reused in better batteries". Gizmag. Retrieved April 2015. Check date values in: |access-date= (help)
  12. ↑ "Silk may be the new 'green' ultra-high-capacity material for batteries". KurzweilAI. March 11, 2015. Retrieved April 2015. Check date values in: |access-date= (help)
  13. ↑ Ye, Jianchao; Ong, Mitchell T.; Heo, Tae Wook; Campbell, Patrick G.; Worsley, Marcus A.; Liu, Yuanyue; Shin, Swanee J.; Charnvanichborikarn, Supakit; Matthews, Manyalibo J. (2015-11-05). "Universal roles of hydrogen in electrochemical performance of graphene: high rate capacity and atomistic origins". Scientific Reports. 5: 16190. doi:10.1038/srep16190. PMC 4633639Freely accessible. PMID 26536830.
  14. ↑ Stark, Anne M. (2015-11-05). "Using hydrogen to enhance lithium-ion batteries". Research & Development. Retrieved 2016-02-10.
  15. ↑ Wang, Yusheng (2015). "Porous graphene for high capacity lithium ion battery anode material". Applied Surface Science. 363: 318–322.
  16. ↑ Lavars, Nick (2016-02-07). "Battery anodes made from pollen are nothing to sneeze at". www.gizmag.com. Retrieved 2016-02-10.
  17. 1 2 3 Researchers Developing Cheap, Better-Performing Lithium-Ion Batteries, Product Design & Development, 1 April 2014, Megan Hazle
  18. ↑ Aricò, Antonino Salvatore; Bruce, Peter; Scrosati, Bruno; Tarascon, Jean-Marie; van Schalkwijk, Walter (May 2005). "Nanostructured materials for advanced energy conversion and storage devices". Nature Materials. 4 (5): 366–377. doi:10.1038/nmat1368. PMID 15867920.
  19. ↑ Chan, Candace K.; Peng, Hailin; Liu, Gao; McIlwrath, Kevin; Zhang, Xiao Feng; Huggins, Robert A.; Cui, Yi (16 December 2007). "High-performance lithium battery anodes using silicon nanowires". Nature Nanotechnology. 3 (1): 31–35. doi:10.1038/nnano.2007.411. PMID 18654447.
  20. ↑ Szczech, Jeannine R.; Jin, Song (2011). "Nanostructured silicon for high capacity lithium battery anodes". Energy Environ. Sci. 4 (1): 56–72. doi:10.1039/C0EE00281J.
  21. ↑ Mack, Eric (2016-01-30). "Lithium-ion battery boost could come from "caging" silicon in graphene". www.gizmag.com. Retrieved 2016-02-07.
  22. ↑ Li, Yuzhang; Yan, Kai; Lee, Hyun-Wook; Lu, Zhenda; Liu, Nian; Cui, Yi (2016). "Growth of conformal graphene cages on micrometre-sized silicon particles as stable battery anodes". Nature Energy. 1 (2): 15029. doi:10.1038/nenergy.2015.29.
  23. ↑ Pomegranate-inspired electrode could mean longer lithium-ion battery life, Gizmag, 19 February 2014, Nick Lavars
  24. ↑ http://helldesign.net (2015-10-27). "Longer-lasting, lighter lithium-ion batteries from silicon anodes | KurzweilAI". www.kurzweilai.net. Retrieved 2016-02-10.
  25. ↑ Hassan, Fathy M.; Batmaz, Rasim; Li, Jingde; Wang, Xiaolei; Xiao, Xingcheng; Yu, Aiping; Chen, Zhongwei (2015-10-26). "Evidence of covalent synergy in silicon-sulfur-graphene yielding highly efficient and long-life lithium-ion batteries". Nature Communications. 6: 8597. doi:10.1038/ncomms9597. PMC 4639807Freely accessible. PMID 26497228.
  26. ↑ Wu, Hui; Chan, Gerentt; Choi, Jang Wook; Ryu, Ill; Yao, Yan; McDowell, Matthew T.; Lee, Seok Woo; Jackson, Ariel; Yang, Yuan; Hu, Liangbing; Cui, Yi (2012). "Stable cycling of double-walled silicon nanotube battery anodes through solid–electrolyte interphase control". Nature Nanotechnology. 7 (5): 310. doi:10.1038/nnano.2012.35. PMID 22447161.
  27. ↑ Chan, C. K.; Peng, H.; Liu, G.; McIlwrath, K.; Zhang, X. F.; Huggins, R. A.; Cui, Y. (2007). "High-performance lithium battery anodes using silicon nanowires". Nature Nanotechnology. 3 (1): 31–35. doi:10.1038/nnano.2007.411. PMID 18654447.
  28. ↑ Amprius Gets $30M Boost for Silicon-Based Lithium-Ion Batteries, Greentech Efficiency, 6 January 2014, Jeff St. John
  29. ↑ "EnerG2 introduces silicon-carbon composite for Li-ion anodes; 5x improvement in cycle life over silicon". Green Car Congress. 2014-01-24. Retrieved 2014-06-19.
  30. 1 2 Borghino, Dario (February 25, 2015). "Going small with silicon potentially has big implications for lithium-ion battery capacity". Gizmag. Retrieved February 2015. Check date values in: |access-date= (help)
  31. ↑ Coxworth, Ben (14 February 2013). Silicon nanoparticles used to create a super-performing battery. Gizmag.com. Retrieved on 16 April 2013.
  32. ↑ "USC team develops new porous silicon nanoparticle material for high-performance Li-ion anodes". Green Car Congress. 2013-02-12. doi:10.1007/s12274-013-0293-y. Retrieved 2013-06-04.
  33. ↑ Sand-based anode triples lithium-ion battery performance, Gizmag, 8 July 2014, Darren Quick
  34. ↑ US Department of Energy doubles lithium-ion battery capacity with spongy silicon, Extreme Tech, 9 July 2014, Sebastian Anthony
  35. ↑ Silicon-hydrogel electrodes improve lithium-ion battery performance, Kurzweil, 4 June 2013
  36. ↑ nanostructure for batteries keeps going and going, Phys.org, 11 May 2012, Mike Ross
  37. ↑ Millikin, Mike (14 August 2011). "SUNY Binghamton researchers show Si/MgO/graphite composite as high-performance Li-ion anode material".
  38. ↑ Zhou, Wenchao; Upreti, Shailesh; Whittingham, M. Stanley (2011-10-31). "High performance Si/MgO/graphite composite as the anode for lithium-ion batteries". Electrochemistry Communications. 13 (10): 1102–1104. doi:10.1016/j.elecom.2011.07.006. Retrieved 2014-02-16.
  39. ↑ electroiq.com. "Northwestern researchers advance Li-ion batteries with graphene-silicon sandwich | Solid State Technology". Electroiq.com. Retrieved 2014-04-28.
    Zhao, X.; Hayner, C. M.; Kung, M. C.; Kung, H. H. (2011). "In-Plane Vacancy-Enabled High-Power Si-Graphene Composite Electrode for Lithium-Ion Batteries". Advanced Energy Materials. 1 (6): 1079. doi:10.1002/aenm.201100426.
  40. ↑ Better Lithium-Ion Batteries Are On The Way From Berkeley Lab, Berkeley Lab, 23 September 2011, Paul Preuss
  41. ↑ WSU Researchers Create Super Lithium-ion Battery Retrieved 2013 January 10
  42. ↑ "Washington State University Gets Funding to Scale Up New Tin Batteries". MacroCurrent. 2013-04-30. Retrieved 2013-06-04.
  43. ↑ Researchers Make Breakthrough in Battery Technology with New Tin-Seeded Germanium Nanowire Anode, World Industrial Reporter, 11 February 2014
  44. ↑ New tin-seeded germanium nanowire array anodes for Li-ion batteries show high capacity and lifetime, Green Car Congress, 10 February 2014
  45. ↑ Garthwaite, Josie (September 15, 2010). "Amprius: Building a Better Battery, from the Anode Up". Gigaom.com. Retrieved 2011-09-26.
  46. ↑ New flexible battery skips the lithium ion, Mumbai Mirror, 30 April 2014
  47. ↑ Higher-Capacity Lithium-Ion Batteries, MIT Technology Review, 22 June 2006, Kevin Bullis
  48. ↑ Martin, Richard (2015-10-25). "New Foam Batteries Promise Fast Charging, Higher Capacity". MIT Technology Review. Retrieved 2016-02-10.
  49. ↑ Palca, Joe (6 April 2009). Hidden Ingredient In New, Greener Battery: A Virus. npr.org; National Public Radio. Retrieved 11 June 2010.
  50. ↑ "New manufacturing process cuts lithium-ion battery cost in half | KurzweilAI". www.kurzweilai.net. June 24, 2015. Retrieved December 16, 2015.
  51. ↑ Younesi, Reza; Veith, Gabriel M.; Johansson, Patrik; Edström, Kristina; Vegge, Tejs (2015). "Lithium salts for advanced lithium batteries: Li–metal, Li–O 2 , and Li–S". Energy Environ. Sci. 8 (7): 1905–1922. doi:10.1039/c5ee01215e.
  52. 1 2 3 4 Bullis, Kevin (February 2, 2015). "A Battery for Electronics That Lasts Twice as Long". Technology Review. Retrieved February 2015. Check date values in: |access-date= (help)
  53. ↑ Bullis, Kevin (December 23, 2014). "A Prototype Battery Could Double the Range of Electric Cars". Technology Review. Retrieved February 2015. Check date values in: |access-date= (help)
  54. 1 2 Borghino, Dario (August 16, 2015). "Aluminum "yolk" nanoparticles deliver high-capacity battery recipe". www.gizmag.com. Retrieved 2015-12-08.
  55. ↑ Subaru doubles the battery range on its electric car concept, Gizmag, 2 November 2007, Loz Blain
  56. ↑ Researchers hard at work to make the workhorse lithium ion battery better, Gigaom, 28 July 2014, Katie Fehrenbacher
  57. ↑ New Rechargeable Cell Has 7 Times Higher Energy Density Than Li-ion Cells, Nikkei Technology, 23 July 2014, Motohiko Hamada
  58. ↑ Researchers develop all-carbon lithium battery, Energy Harvesting Journal, 28 April 2014
  59. ↑ Messy Innards Make for a Better Lithium Ion Battery, Scientific American, 17 January 2014, Umair Irfan and ClimateWire
  60. ↑ "Glass for battery electrodes". R&D. 01/13/20. Retrieved February 2015. Check date values in: |access-date=, |date= (help)
  61. ↑ A123 Systems introduces new Nanophosphate EXT Li-ion battery technology with optimized performance in extreme temperatures; OEM micro-hybrid program due next year, Green Car Congress, 12 June 2012
  62. ↑ A123's new battery tech goes to extremes, EE Times, 12 June 2012
  63. ↑ Poizot, P. (2000). "Nano-sized transition-metal oxides as negative-electrode materials for lithium-ion batteries". Nature. 407: 496–499.
  64. ↑ "Seawater battery sparks sub dreams". New Scientist. 25 April 2012. Retrieved 22 June 2012.
  65. ↑ Plant root used to create eco-friendly lithium-ion battery, Gizmag, 11 December 2012, Darren Quick
  66. ↑ Batteries charge very quickly and retain capacity, thanks to new structure, News Bureau Illinois, 21 March 2011, Liz Ahlberg
  67. ↑ Small in size, big on power: New microbatteries a boost for electronics, News Bureau Illinois, 16 April 2013, Liz Ahlberg
  68. ↑ High-power lithium ion microbatteries from interdigitated three-dimensional bicontinuous nanoporous electrodes., US National Library of Medicine National Institutes of Health
  69. ↑ Report: Nissan On Track with Nickel Manganese Cobalt Li-ion Cell for Deployment in 2015, Green Car Congress, 12 August 2014
  70. ↑ Re-engineered battery material could lead to rapid recharging of many devices, MIT News, 11 March 2009, Elizabeth A. Thomson
  71. ↑ Zyga, Lisa (12 March 2009). "Nanoball Batteries Could Charge Electric Cars in 5 Minutes". PhysOrg. Retrieved 21 March 2012.
  72. ↑ "A 'breakthrough' in rechargeable batteries for electronic devices and electric vehicles". KurzweilAI. February 26, 2015. Retrieved April 2015. Check date values in: |access-date= (help)
  73. ↑ Yang, X. F.; Yang, J.-H.; Zaghib, K.; Trudeau and, M. L.; Ying, J. Y. (March 2015 Pp= 305–313). "Synthesis of phase-pure Li2MnSiO4@C porous nanoboxes for high-capacity Li-ion battery cathodes.". Nano Energy. 12: 305–313. doi:10.1016/j.nanoen.2014.12.021. Check date values in: |date= (help)
  74. ↑ Better batteries through biology, Kurzweil Accelerating Technology, 15 November 2013
  75. ↑ Kumar, B.; Kumar, J.; Leese, R.; Fellner, J. P.; Rodrigues, S. J.; Abraham, K. M. (2010). "A Solid-State, Rechargeable, Long Cycle Life Lithium–Air Battery". Journal of the Electrochemical Society. 157: A50. doi:10.1149/1.3256129.
  76. ↑ "Researchers Develop Solid-State, Rechargeable Lithium-Air Battery; Potential to Exceed 1,000 Wh/kg". Green Car Congress. 2009-11-21. Retrieved 2013-08-28.
  77. ↑ Researchers Analyze Atomic-Scale Electronic and Structural Degradation in Lithium-Ion Batteries, AZO Materials, 30 October 2014, Alessandro Pirolini
  78. ↑ Nissan develops world first analysis technique for better lithium ion battery durability, Automotive World, 13 March 2014
  79. ↑ How Lithium-Ion Batteries Age: Scientists Offer Insight, Green Car Reports, 21 March 2014, Stephen Edelstein
  80. ↑ Researchers Observe The Phenomenon Of "Lithium Plating" During The Charging Process, Red Orbit, 4 September 2014, Ralph Gilles
  81. ↑ Stressed out: Research sheds new light on why rechargeable batteries fail, Phys.org, 01 October 2014, Marcia Goodrich
  82. ↑ Szondy, David (2015-06-15). "Additives keep lithium-ion batteries from catching fire". www.gizmag.com. Retrieved 2016-02-10.
  83. ↑ Stanford scientists create a 'smart' lithium-ion battery that warns of fire hazard, Phys.org, 13 October 2014
  84. ↑ Coxworth, Ben (January 28, 2015). "Kevlar-reinforced lithium-ion batteries shouldn't catch fire". Gizmag. Retrieved April 2015. Check date values in: |access-date= (help)
  85. ↑ Casa, Nicole (2015-01-28). ""Bulletproof" battery". R&D. Retrieved February 2015. Check date values in: |access-date= (help)
  86. ↑ First nonflammable lithium-ion battery will stop your smartphone, car, and plane from exploding, Extreme Tech, 13 February 2014, Sebastian Anthony
  87. ↑ Chewing gum-like material makes lithium ion batteries safer, Tree Hugger, 5 February 2014, Megan Treacy
  88. ↑ "Rechargeable batteries with almost infinite lifetimes coming, say MIT-Samsung engineers". www.kurzweilai.net. 2015-08-24. Retrieved 2016-02-10.
  89. 1 2 Jeffrey, Colin (March 2, 2015). "New electrolyte promises to rid lithium batteries of short-circuiting dendrites". Retrieved April 2015. Check date values in: |access-date= (help)
  90. ↑ Lavars, Nick (May 4, 2014). "Dual-functioning electrolyte improves capacity of long-life batteries". Gizmag. Retrieved April 2015. Check date values in: |access-date= (help)
  91. ↑ "Superhalogens as Building Blocks of Halogen-Free Electrolytes in Lithium-Ion Batteries†". Angewandte Chemie. 126 (50): 14136–14139. 14 October 2014. doi:10.1002/ange.201408648. |first1= missing |last1= in Authors list (help)
  92. ↑ McNeill, Brian (2014-10-24). "Physicists find toxic halogens in Li-ion batteries".
  93. ↑ Want lithium-ion batteries to last? Slow charging may not be the answer, PC World
  94. ↑ Why Lithium Ion Batteries Go Bad, Product Design & Development, 15 September 2014
  95. ↑ Software on your smartphone can speed up lithium-ion battery charging by up to 6x, Extreme Tech, 14 August 2014, Sebastian Anthony
  96. ↑ StoreDot Wants to Charge Your EV in 5 Minutes
  97. ↑ New battery management technology could boost Li-ion capacity by 40%, quadruple recharging cycles, TreeHugger, 5 February 2014, Derek Markham
  98. ↑ Long-life laptop battery the tech industry doesn’t want you to have, The Globe and Mail, 6 February 2014, Jordana Divon
  99. ↑ "Stanford researchers develop heat-sensitive batteries". ZME Science. Retrieved 2016-02-07.
  100. ↑ Chen, Zheng; Hsu, Po-Chun; Lopez, Jeffrey; Li, Yuzhang; To, John W. F.; Liu, Nan; Wang, Chao; Andrews, Sean C.; Liu, Jia (2016-01-11). "Fast and reversible thermoresponsive polymer switching materials for safer batteries". Nature Energy. 1 (1): 15009. doi:10.1038/nenergy.2015.9.
  101. ↑ Origami: The surprisingly simple secret to creating flexible, high-power lithium-ion batteries, Extreme Tech, 5 February 2014, Sebastian Anthony
  102. ↑ Sandhana, Lakshmi (May 30, 2014). "Scientists create weavable Li-ion fiber battery yarn". Gizmag. Retrieved February 2015. Check date values in: |access-date= (help)
  103. ↑ Lovering, Daniel (July 18, 2014). "Flexible, Printed Batteries for Wearable Devices". Technology Review. Retrieved February 2015. Check date values in: |access-date= (help)
  104. ↑ Borghino, Dario (May 2, 2014). "Flexible, high-performance battery could soon find its way to your smartwatch". Gizmag. Retrieved February 2015. Check date values in: |access-date= (help)
  105. ↑ https://www.insplorion.com/en/news/cooperation-with-agm-batteries-ltd-in-full-swing/
This article is issued from Wikipedia - version of the 11/10/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.