Light-gas gun

A light-gas gun at Rice University. Using hydrogen gas and powered by a shotgun shell, it achieves a velocity of 7 km/s. Used during the development of the Gamma-ray Large Area Space Telescope shield.

The light-gas gun is an apparatus for physics experiments, a highly specialized gun designed to generate very high velocities. It is usually used to study high-speed impact phenomena (hypervelocity research), such as the formation of impact craters by meteorites or the erosion of materials by micrometeoroids. Some basic materials research relies on projectile impact to create high pressure: such systems are capable of forcing liquid hydrogen into a metallic state.

Operation

A light-gas gun works on the same principle as a spring piston airgun. A large-diameter piston is used to force a gaseous working fluid through a smaller-diameter barrel containing the projectile to be accelerated. This reduction in diameter acts as a lever, increasing the speed while decreasing the force. In an airgun, the large piston is powered by a spring or compressed air, and the working fluid is atmospheric air.

In a light-gas gun, the piston is powered by a chemical reaction (usually gunpowder), and the working fluid is a lighter gas, such as helium or hydrogen (though helium is much safer to work with, hydrogen offers the best performance [as explained below] and causes less launch-tube erosion). One addition that a light-gas gun adds to the airgun is a rupture disk, which is a disk (usually metal) of carefully calibrated thickness designed to act as a valve. When the pressure builds up to the desired level behind the disk, the disk tears open, allowing the high-pressure, light gas to pass into the barrel. This ensures that the maximum amount of energy is available when the projectile begins moving.

Diagram of a light-gas gun
1 — Breech block
2 — Chamber
3 — Propellant charge (gunpowder)
4 — Piston
5 — Pump tube
6 — Light gas (helium or hydrogen)
7 — Rupture disk
8 — High pressure coupling
9 — Projectile
10 — Gun barrel

One particular light-gas gun used by NASA uses a modified 40–mm cannon for power. The cannon uses gunpowder to propel a plastic (usually HDPE) piston down the cannon barrel, which is filled with high-pressure hydrogen gas. At the end of the cannon barrel is a conical section, leading down to the 5-mm barrel that fires the projectile. In this conical section is a stainless steel disk, approximately 2 mm thick, with an "x" pattern scored into the surface in the middle. When the hydrogen develops sufficient pressure to burst the scored section of the disk, the hydrogen flows through the hole and accelerates the projectile to a velocity of 6 km/s (22,000 km/h) in a distance of about a meter.

NASA also operates light-gas guns with launch tube sizes ranging from 0.170 inches (4.3 mm) to 1.5 in (38 mm) at Ames Research Center. Hazardous testing[1] is conducted at White Sands Test Facility. These guns have been used in support of various missions beginning with Apollo program reentry studies in the 1960s and most recently for high-speed thermal imaging. Velocities ranging from 1 km/s up to 8.5 km/s can be achieved. The largest of these involves a 6.25-inch (159 mm) diameter piston weighing more than 46 pounds (21 kg) to compress the hydrogen.

Two light-gas guns at Arnold Air Force Base's Hypervelocity Ballistics Ranges.

Arnold Air Force Base's Range-G is the "largest routinely operated two-stage, light-gas gun system in the United States".[2] Range-G utilizes interchangeable launch tubes ranging from a bore diameter of 3.3 inches (84 mm) to 8.0 inches (200 mm) with a 14.0-inch (360 mm) piston weighing up to 2,300 pounds (1,000 kg). Projectile velocities can reach 4.5 kilometres per second (16,000 km/h) for the 8.0-inch (200 mm) configuration and 7 kilometres per second (25,000 km/h) for the 3.3-inch (84 mm) launcher configuration.[2] The primary use of the range facilities at Arnold Air Force Base is the measurement of released kinetic energy upon projectile impact.

Design physics

The limiting factor on the speed of an airgun, firearm, or light-gas gun is the speed of sound in the working fluid—the air, burning gunpowder, or a light gas. This is essentially because the projectile is accelerated by the pressure difference between its ends, and such a pressure wave cannot propagate any faster than the speed of sound in the medium. The speed of sound in helium is about three times that in air, and in hydrogen 3.8 times that in air.

The speed of sound also increases with the temperature of the fluid (but is independent of the pressure), so the heat formed by the compression of the working fluid serves to increase the maximum possible speed. Spring piston airguns increase the temperature of the air in the chamber by adiabatic heating; this raises the local speed of sound enough to overcome frictional and other efficiency losses and propel the projectile at more than the speed of sound in the ambient conditions.

Hybrid electrothermal light-gas gun

The hybrid electrothermal light-gas gun works on similar principles of the standard light-gas gun, but adds an electric arc to heat the light gas to a higher temperature and pressure than the piston alone. The arc is applied in the chamber containing the light gas, raising the temperature and pressure to the point where the gas both breaks the bursting disk and ignites the propellant behind the piston, which is perforated to allow ignition. The resulting combination of electrical heating and piston compression provide higher pressures and temperatures, resulting in more power and a higher potential speed than a standard light-gas gun.[3][4]

Impact profile

When the projectile fired by a gas gun impacts its target, the pressure applied depends upon the mass of the projectile and the area or cross-section over which the impact force is distributed. Obviously, a dense, narrow projectile will apply more pressure overall than a light and wide one. Looking at constant cross-sectional projectiles, researchers have recently begun to vary their projectiles' density as a function of length. Since the projectiles travel at a known velocity, changes in density as a function of length have a predictable relationship to the impact pressure applied as a function of time. With materials in a wide range of densities (from tungsten powder to glass microspheres) applied in thin layers, carefully made projectiles can be used in constant-pressure experiments, or even controlled compression–expansion–compression sequences.

See also

References

  1. ↑ "Remote Hypervelocity Test Facility". NASA. 2014-07-31.
  2. 1 2 "Hypervelocity Range Facility". Arnold Air Force Base. 2008-12-11.
  3. ↑ US 5429030 Hybrid electrothermal light gas gun and method
  4. ↑ Hybrid electrothermal light-gas gun and method, United States Patent 5,429,030 Tidman July 4, 1995

External links

This article is issued from Wikipedia - version of the 9/4/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.