Hells Canyon Dam

Hells Canyon Dam

Aerial view of the dam
Location Hells Canyon, Adams County, Idaho /
Wallowa County, Oregon
United States
Coordinates 45°14′41″N 116°41′54″W / 45.24472°N 116.69833°W / 45.24472; -116.69833Coordinates: 45°14′41″N 116°41′54″W / 45.24472°N 116.69833°W / 45.24472; -116.69833
Opening date 1967
Operator(s) Idaho Power Company
Dam and spillways
Impounds Snake River
Height 100 m (330 ft)
Reservoir
Creates Hells Canyon Reservoir
Total capacity 232,000,000 m3 (188,000 acre·ft)
Catchment area 189,800 km2 (73,300 sq mi)
Surface area 10 km2 (3.9 sq mi)
Power station
Installed capacity 391 MW
Annual generation 2,051.3 GWh

Hells Canyon Dam is a concrete gravity dam on the Snake River (river mile 247) in Hells Canyon on the Idaho-Oregon border. The dam impounds the Snake River in Hells Canyon Reservoir; its spillway elevation is 512 m (1,680 ft) above sea level.

It is the third and final hydroelectric dam of the Hells Canyon Project, which includes Brownlee Dam (1959) and Oxbow Dam (1961), all built and operated by Idaho Power Company. The Hells Canyon Complex on the Snake River is the largest privately owned hydroelectric power complex in the nation, according to the US Energy Information Administration.[1] The contractor for the Hells Canyon Dam was Morrison-Knudsen.

The Hells Canyon Dam powerhouse contains three generating units, with a total nameplate capacity of 391 megawatts (MW).[2] Power generation began with two units in 1967, the third came on line the following year.

Lacking passage for migrating salmon, the three dams of the Hells Canyon Project blocked access by anadromous salmonids to a stretch of the Snake River drainage basin from Hells Canyon Dam up to Shoshone Falls, which naturally prevents any upstream fish passage to the upper Snake River basin.

High dam proposal

As built, Hells Canyon Dam is significantly lower than it was originally proposed in the 1940s, with three dams (Hells Canyon, Brownlee Dam and Oxbow Dam) taking the place of a single 710-foot (220 m) high dam.[3] As proposed by the U.S. Army Corps of Engineers, the Hells Canyon High Dam would have been a straight-profile concrete gravity dam with two gate-controlled tunnel spillways, one in each abutment. The proposed reservoir was planned to have a capacity of 4,050,000 acre feet (5.00 km3) with an area of 23,500 acres (9,500 ha). The reservoir was to extend 89 miles (143 km) upstream. The power plant was to be capable of generating 850 MW using ten units. The project included provisions for fish hatcheries, with the intention of maintaining salmon runs. Project cost was estimated at $342,076,000.[4] The high dam project was not pursued.

Proposed Hells Canyon High Dam

See also

References

  1. ↑ "State Energy Profiles: Idaho". U.S. Department of Energy. December 23, 2010. Retrieved December 27, 2010.
  2. ↑ "Hells Canyon Dam – General Information". Columbia Basin Research, University of Washington. Retrieved December 27, 2010.
  3. ↑ "Hells Canyon". Idaho Power. Retrieved 6 June 2011.
  4. ↑ "61st Congress, 2d Session, House Document No. 581, Report: Columbia River and Tributaries, Northwestern United States". Army Corps of Engineers. March 20, 1950. p. 214.
Wikimedia Commons has media related to Hells Canyon Dam.
This article is issued from Wikipedia - version of the 10/25/2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.