System Architecture Evolution

System Architecture Evolution (SAE) is the core network architecture of 3GPP's LTE wireless communication standard.

SAE is the evolution of the GPRS Core Network, with some differences:

• simplified architecture
• all-IP Network (AIPN)
• support for higher throughput and lower latency radio access networks (RANs)
• support for, and mobility between, multiple heterogeneous access networks, including E-UTRA (LTE and LTE Advanced air interface), 3GPP legacy systems (for example GERAN or UTRAN, air interfaces of GPRS and UMTS respectively), but also non-3GPP systems (for example WiFi, WiMAX or cdma2000)

SAE Architecture

The SAE has a flat, all-IP architecture with separation of control plane and user plane traffic.

The main component of the SAE architecture is the Evolved Packet Core (EPC), also known as SAE Core. The EPC will serve as the equivalent of GPRS networks (via the Mobility Management Entity, Serving Gateway and PDN Gateway subcomponents).

EPC nodes and interfaces

The subcomponents of the EPC are:^[1][2]

• MME (Mobility Management Entity): The MME is the key control-node for the LTE access-network. It is responsible for idle mode UE (User Equipment) paging and tagging procedure including retransmissions. It is involved in the bearer activation/deactivation process and is also responsible for choosing the SGW for a UE at the initial attach and at time of intra-LTE handover involving Core Network (CN) node relocation. It is responsible for authenticating the user (by interacting with the HSS). The Non Access Stratum (NAS) signaling terminates at the MME and it is also responsible for generation and allocation of temporary identities to UEs. It checks the authorization of the UE to camp on the service provider’s Public Land Mobile Network (PLMN) and enforces UE roaming restrictions. The MME is the termination point in the network for ciphering/integrity protection for NAS signaling and handles the security key management. Lawful interception of signaling is also supported by the MME. The MME also provides the control plane function for mobility between LTE and 2G/3G access networks with the S3 interface terminating at the MME from the SGSN. The MME also terminates the S6a interface towards the home HSS for roaming UEs.
• SGW (Serving Gateway): The SGW routes and forwards user data packets, while also acting as the mobility anchor for the user plane during inter-eNodeB handovers and as the anchor for mobility between LTE and other 3GPP technologies (terminating S4 interface and relaying the traffic between 2G/3G systems and PGW). For idle state UEs, the SGW terminates the downlink data path and triggers paging when downlink data arrives for the UE. It manages and stores UE contexts, e.g. parameters of the IP bearer service, network internal routing information. It also performs replication of the user traffic in case of lawful interception.
• PGW (PDN Gateway): The PDN Gateway provides connectivity from the UE to external packet data networks by being the point of exit and entry of traffic for the UE. A UE may have simultaneous connectivity with more than one PGW for accessing multiple PDNs. The PGW performs policy enforcement, packet filtering for each user, charging support, lawful interception and packet screening. Another key role of the PGW is to act as the anchor for mobility between 3GPP and non-3GPP technologies such as WiMAX and 3GPP2 (CDMA 1X and EvDO).
• HSS (Home Subscriber Server): The HSS is a central database that contains user-related and subscription-related information. The functions of the HSS include functionalities such as mobility management, call and session establishment support, user authentication and access authorization. The HSS is based on pre-Rel-4 Home Location Register (HLR) and Authentication Center (AuC).
• ANDSF (Access Network Discovery and Selection Function): The ANDSF provides information to the UE about connectivity to 3GPP and non-3GPP access networks (such as Wi-Fi). The purpose of the ANDSF is to assist the UE to discover the access networks in their vicinity and to provide rules (policies) to prioritize and manage connections to these networks.
• ePDG (Evolved Packet Data Gateway): The main function of the ePDG is to secure the data transmission with a UE connected to the EPC over an untrusted non-3GPP access. For this purpose, the ePDG acts as a termination node of IPsec tunnels established with the UE.

Non Access Stratum (NAS) protocols

The Non-Access Stratum (NAS) protocols form the highest stratum of the control plane between the user equipment (UE) and MME.^[3] NAS protocols support the mobility of the UE and the session management procedures to establish and maintain IP connectivity between the UE and a PDN GW. They define the rules for a mapping between parameters during inter-system mobility with 3G networks or non-3GPP access networks. They also provide the NAS security by integrity protection and ciphering of NAS signaling messages. EPS provides the subscriber with a "ready-to-use" IP connectivity and an "always-on" experience by linking between mobility management and session management procedures during the UE attach procedure.

Complete NAS transactions consist of specific sequences of elementary procedures with EPS Mobility Management (EMM) and EPS Session Management (ESM) protocols.

EMM (EPS Mobility Management)

The EPS Mobility Management (EMM) protocol provides procedures for the control of mobility when the User Equipment (UE) uses the Evolved UMTS Terrestrial Radio Access Network (E-UTRAN). It also provides control of security for the NAS protocols.

EMM involves different types of procedures such as:

• EMM common procedures — can always be initiated while a NAS signalling connection exists. The procedures belonging to this type are initiated by the network. They include GUTI reallocation, authentication, security mode control, identification and EMM information.
• EMM specific procedures — specific to the UE only. At any time only one UE-initiated EMM specific procedure can run. The procedures belonging to this type are attach and combined attach, detach or combined detach, normal tracking area update and combined tracking area update (S1 mode only) and periodic tracking area update (S1 mode only).
• EMM connection management procedures — manage the connection of the UE with the network:
  • Service request: Initiated by the UE and used to establish a secure connection to the network or to request the resource reservation for sending data, or both.
  • Paging procedure: Initiated by the network and used to request the establishment of a NAS signalling connection or to prompt the UE to re-attach if necessary as a result of a network failure.
  • Transport of NAS messages: Initiated by the UE or the network and used to transport SMS messages.
  • Generic transport of NAS messages: Initiated by the UE or the network and used to transport protocol messages from other applications.

The UE and the network execute the attach procedure, the default EPS bearer context activation procedure in parallel. During the EPS attach procedure the network activates a default EPS bearer context. The EPS session management messages for the default EPS bearer context activation are transmitted in an information element in the EPS mobility management messages. The UE and network complete the combined default EPS bearer context activation procedure and the attach procedure before the dedicated EPS bearer context activation procedure is completed. The success of the attach procedure is dependent on the success of the default EPS bearer context activation procedure. If the attach procedure fails, then the ESM session management procedures also fails.

ESM (EPS Session Management)

The EPS Session Management (ESM) protocol provides procedures for the handling of EPS bearer contexts. Together with the bearer control provided by the Access Stratum, it provides the control of user plane bearers. The transmission of ESM messages is suspended during EMM procedures except for the attach procedure.

EPS Bearer: Each EPS bearer context represents an EPS bearer between the UE and a PDN. EPS bearer contexts can remain activated even if the radio and S1 bearers constituting the corresponding EPS bearers between UE and MME are temporarily released. An EPS bearer context can be either a default bearer context or a dedicated bearer context. A default EPS bearer context is activated when the UE requests a connection to a PDN. The first default EPS bearer context, is activated during the EPS attach procedure. Additionally, the network can activate one or several dedicated EPS bearer contexts in parallel.

Generally, ESM procedures can be performed only if an EMM context has been established between the UE and the MME, and the secure exchange of NAS messages has been initiated by the MME by use of the EMM procedures. Once the UE is successfully attached, the UE can request the MME to set up connections to additional PDNs. For each additional connection, the MME activates a separate default EPS bearer context. A default EPS bearer context remains activated throughout the lifetime of the connection to the PDN.

Types of ESM procedures: ESM involves different types of procedures such as:

• EPS bearer contexts procedures — initiated by the network and are used for the manipulation of EPS bearer contexts, including Default EPS bearer context activation, Dedicated EPS bearer context activation, EPS bearer context modification, EPS bearer context deactivation.
• Transaction related procedures — initiated by the UE to request for resources, i.e. a new PDN connection or dedicated bearer resources, or to release these resources. They include PDN connectivity procedure, PDN disconnect procedure, Bearer resource allocation procedure, Bearer resource modification procedure.

The MME maintains EMM context and EPS bearer context information for UEs in the ECM-IDLE, ECM CONNECTED and EMM-DEREGISTERED states.

EPC protocol stack

MME (Mobility Management Entity) protocols

The MME protocol stack consists of:

1. S1-MME stack to support S1-MME interface with eNodeB
2. S11 stack to support S11 interface with Serving Gateway

MME supports the S1 interface with eNodeB. The integrated S1 MME interface stack consists of IP, SCTP, S1AP.

• SCTP (Stream Control Transmission Protocol) is a common transport protocol that uses the services of Internet Protocol (IP) to provide a reliable datagram delivery service to the adaptation modules, such as the S1AP. SCTP provides reliable and sequenced delivery on top of the existing IP framework. The main features provided by SCTP are:
  • Association setup: An association is a connection that is set up between two endpoints for data transfer, much like a TCP connection. A SCTP association can have multiple addresses at each end.
  • Reliable Data Delivery: Delivers sequenced data in a stream (Elimination of head-of-line blocking): SCTP ensures the sequenced delivery of data with multiple unidirectional streams, without blocking the chunks of data in other direction.
• S1AP (S1 Application Part) is the signaling service between E-UTRAN and the Evolved Packet Core (EPC) that fulfills the S1 Interface functions such as SAE Bearer management functions, Initial context transfer function, Mobility functions for UE, Paging, Reset functionality, NAS signaling transport function, Error reporting, UE context release function, Status transfer.

MME supports S11 interface with Serving Gateway. The integrated S11 interface stack consists of IP, UDP, eGTP-C.

SGW (Serving Gateway) protocols

The SGW consists of

1. S11 control plane stack to support S11 interface with MME
2. S5/S8 control and data plane stacks to support S5/S8 interface with PGW
3. S1 data plane stack to support S1 user plane interface with eNodeB
4. S4 data plane stack to support S4 user plane interface between RNC of UMTS and SGW of eNodeB

SGW supports S11 interface with MME and S5/S8 interface with PGW. The integrated control plane stack for these interfaces consists of IP, UDP, eGTP-C.

SGW supports the S1-U interface with eNodeB and S5/S8 data plane interface with PGW. The integrated data plane stack for these interfaces consists of IP, UDP, eGTP-U.

PGW (Packet Data Network Gateway) protocols

The PGW consists of S5/S8 control and data plane stacks to support S5/S8 interface with SGW.

PGW supports S5/S8 interface with Serving Gateway. The integrated control plane stack for the S5/S8 interfaces consists of IP, UDP, eGTP-C.

The integrated data plane stack for the S5/S8 interface consists of IP, UDP, eGTP-U.

Support of voice services and SMS

The EPC is a packet-only core network. It does not have a circuit-switched domain, which is traditionally used for phone calls and SMS.

3GPP specified two solutions for voice:

• IMS: A solution for IMS Voice over IP was specified in Rel-7.
• Circuit-Switched fallback (CSFB): in order to make or receive calls, the UE changes its radio access technology from LTE to a 2G/3G technology that supports circuit-switched services. This feature requires 2G/3G coverage. A new interface (called SGs) between the MME and the MSC is required. This feature was developed in Rel-8.

3GPP specified two solutions for SMS:

• IMS: A solution for SMS over IP was specified in Rel-7.
• SMS over SGs: this solution requires the SGs interface introduced during the work on CSFB. SMS are delivered in the Non Access Stratum over LTE. There is no inter-system change for sending or receiving SMS. This feature was specified in Rel-8.

CSFB and SMS over SGs are seen as interim solutions, the long term being IMS.^[4]

Multiple access networks

The UE can connect to the EPC using several access technologies. These access technologies are composed of:

• 3GPP accesses: these access technologies are specified by the 3GPP. They include GPRS, UMTS, EDGE, HSPA, LTE and LTE Advanced.
• non-3GPP accesses: these access technologies are not specified by the 3GPP. They include technologies such as cdma2000, WiFi or fixed networks. 3GPP specifies two classes of non-3GPP access technologies with different security mechanisms:
  • trusted accesses, that the network operator consider trustable from a security stand point (for example: a cdma2000 network). Trusted non-3GPP accesses interface directly with the network.
  • untrusted accesses, that the network operator doesn't consider trustable from a security stand point (for example, a connection over a public WiFi hotspot). Untrusted non-3GPP accesses are connected to the network via an ePDG, which provide additional security mechanisms (IPsec tunneling).

It is up to the network operator to decide whether a non-3GPP access technology is trusted or untrusted.

It is worth noting that these trusted/untrusted categories do not apply to 3GPP accesses.

3GPP releases

The 3GPP delivers standards in parallel releases, which compose consistent sets of specifications and features.

Further reading

• 3GPP page on SAE
• 3GPP TS 23.401: General Packet Radio Service (GPRS) enhancements for Evolved Universal Terrestrial Radio Access Network (E-UTRAN) access
• 3GPP TS 23.402: 3GPP System Architecture Evolution
• 3GPP LTE-SAE Overview, by Ulrich Barth (SAE in 2006)

See also

• LTE

References

• LTE White Paper: "Long Term Evolution (LTE):A Technical Overview". Motorola. 
• Strategic White Paper: "Introduction to Evolved Packet Core" (PDF). Alcatel-Lucent. 
• Technical White Paper: "Evolved Packet Core solution: Innovation in LTE core" (PDF). Alcatel-Lucent.