Wind resource assessment

Wind resource assessment is the process by which wind power developers estimate the future energy production of a wind farm. Accurate wind resource assessments are crucial to the successful development of wind farms.

History

Modern wind resource assessments have been conducted since the first wind farms were developed in the late 1970s. The methods used were pioneered by developers and researchers in Denmark, where the modern wind power industry first developed.

Wind resource maps

Wind resource map for the windiest U.S. state, North Dakota

Government agencies in some countries publish maps (commonly collected together as a national 'wind atlas') of estimated wind resources, which serve to inform policy-making and encourage wind power development. Examples include the Canadian Wind Atlas, the European Wind Atlas, and the Wind Resource Atlas of the United States. Recognizing the lack of knowledge of wind (and solar) resource potential in developing countries, the Solar and Wind Energy Resource Assessment (SWERA) project was initiated by the United Nations Environment Program in 2002, with funding from the Global Environment Facility, to carry out initial mapping using only satellite-based data.[1] More recently the Energy Sector Management Assistance Program (ESMAP), a program within the World Bank, has launched an initiative to map wind and other renewable energy resources in a number of developing countries, with the intention of developing high quality mapping outputs (and associated datasets) that are validated with specially commissioned ground-based data.[2] There is also an ongoing effort by the International Renewable Energy Agency (IRENA) to create a Global Atlas for Renewable Energy, which brings together publicly available GIS data on wind and other renewable energy resources.

Wind prospecting can begin with the use of such maps, but the lack of accuracy and fine detail make them useful only for preliminary selection of sites for collecting wind speed data.[3] With increasing numbers of ground-based measurements from specially installed anemometer stations, as well as operating data from commissioned wind farms, the accuracy of wind resource maps in many countries has improved over time, although coverage in most developing countries is still patchy. In addition to the publicly available sources listed above, maps are available as commercial products through specialist consultancies, or users of GIS software can make their own using publicly available GIS data such as the US National Renewable Energy Laboratory's High Resolution Wind Data Set.[4]

Although the accuracy has improved, it is unlikely that wind resource maps, whether public or commercial, will eliminate the need for on-site measurements for utility-scale wind generation projects.[5] However, mapping can help speed up the process of site identification and the existence of high quality, ground-based data can shorten the amount of time that on-site measurements need to be collected.

Measurements

To estimate the energy production of a wind farm, developers must first measure the wind on site. Meteorological towers equipped with anemometers, wind vanes, and sometimes temperature, pressure, and relative humidity sensors are installed. Data from these towers must be recorded for at least one year to calculate an annually representative wind speed frequency distribution.

Since onsite measurements are usually only available for a short period, data is also collected from nearby long-term reference stations (usually at airports). This data is used to adjust the onsite measured data so that the mean wind speeds are representative of a long-term period for which onsite measurements are not available. Versions of these maps can be seen and used with software applications such as windNavigator.

Calculations

The following calculations are needed to accurately estimate the energy production of a proposed wind farm project:

Software applications

Main article: Wind energy software

Wind power developers use various types of software applications to assess wind resources.

Wind data management

Wind data management software assists the user in gathering, storing, retrieving, analyzing, and validating wind data. Typically the wind data sets are collected directly from a data logger, located at a meteorological monitoring site, and are imported into a database. Once the data set is in the database it can be analyzed and validated using tools built into the system or it can be exported for use in external wind data analysis software, wind flow modeling software, or wind farm modeling software.

Many data logger manufacturers offer wind data management software that is compatible with their logger. These software packages will typically only gather, store, and analyze data from the manufacturer's own loggers.

Third party data management software and services exist that can accept data from a wide variety of loggers and offer more comprehensive analysis tools and data validation.

Wind data analysis

Wind data analysis software assist the user in removing measurement errors from wind data sets and perform specialized statistical analysis.

Atmospheric simulation modeling

Wind flow modeling methods, described in the following section, named 'Wind flow modeling', provide insights into very high-resolution wind flow behavior, often, at horizontal resolution finer than 100-m. Because of such finest resolution computational fluid dynamics (CFD) modeling application, the typical model domains used by these small-scale models have a few kilometers in the horizontal direction and several hundred meters in the vertical direction. The above-mentioned model domain limitations by small-scale CFD models, need to be addressed and are often addressed by atmospheric CFD models, that could cover horizontal model domains on the order of hundreds of kilometers and vertical domain depths of tens of kilometers. In other words, any atmospheric processes that occur within such large-scale atmospheric model domains, that will influence site-specific wind and its temporal variation should be captured for successful wind resource assessment. This class of atmospheric CFD models and their contribution has not been fully explored and adopted yet, although the aforementioned atmospheric influences captured by such models are highly relevant and critical for the overall wind resource assessment efforts. There are a few such atmospheric CFD models being applied for wind resource assessments today.

Wind flow modeling

Wind flow modeling software aims to predict important characteristics of the wind resource at locations where measurements are not available. The most commonly used such software application is WAsP, created at Risø National Laboratory in Denmark. WAsP uses a potential flow model to predict how wind flows over the terrain at a site. WindSim is a similar application that uses CFD calculations instead, which are potentially more accurate, particularly for complex terrains. Fluidyn PANEOLE is another software based on CFD, which makes it a high precision tool capable of generating wind field atlas for wind farm siting, while also integrating wake effects. It generates a wind field atlas for efficient positioning of turbines. Fluidyn PANEOLE also includes local boundary layer effects such as flow detachment, venturi effect between hills or large buildings, surface roughness generated turbulence or sea breeze.

Wind farm modeling

Wind farm modeling software aims to simulate the behavior of a proposed or existing wind farm, most importantly to calculate its energy production. The user can usually input wind data, height and roughness contour lines, wind turbine specifications, background maps, and define objects that represent environmental restrictions. This information is then used to design a wind farm that maximizes energy production while taking restrictions and construction issues into account. There are several wind farm modeling software applications available, including Openwind, Windfarmer, WindPRO, WindSim, Fluidyn PANEOLE, meteodyn WT and WAsP.

Medium scale wind farm modelling

In recent years a new breed of wind farm development has grown from the increased need for distributed generation of electricity from local wind resources. This type of wind projects is mostly driven by land owners with high energetic requirements such as farmers and industrial site managers. A particular requirement from a wind modelling point of view is the inclusion of all local features such as trees, hedges and buildings as turbine hub-heights range from as little as 10m to 50m. Wind modelling approaches need to include these features but very few of the available wind modelling commercial software provide this capability. Several work groups have been set up around the world to look into this modelling requirement and companies including Digital Engineering Ltd (UK), NREL (USA), DTU Wind Energy (Denmark) are at the forefront of development in this area and look at the application of meso-CFD wind modelling techniques for this purpose.

References

  1. ↑ http://en.openei.org/datasets/files/721/pub/infosheet_10.pdf
  2. ↑ http://esmap.org/RE_mapping
  3. ↑ Bailey, Bruce H.; McDonald, Scott L.; Bernadett, Daniel W.; Markus, Michael J.; Elsholz, Kurt V. (April 1997). "Wind Resource Assessment Handbook" (PDF). Subcontract No. TAT-5-15283-01. National Renewable Energy Laboratory. Retrieved 2009-01-28.
  4. ↑ http://www.nrel.gov/gis/data_wind.html
  5. ↑ http://www.awea.org/faq/wwt_basics.html
This article is issued from Wikipedia - version of the 2/17/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.