Thunderbolt tank

Australian Cruiser Tank Mk. 3 "Thunderbolt"
The pilot production AC MkIII tank
Type Cruiser tank
Place of origin Australia
Production history
Designed 1942
Manufacturer New South Wales Railway Company
Produced 1943
Number built 1
Specifications
Weight 29 long tons (29.5 t)[1]
Length 20 feet 9 inches (6.32 m)
Width 9 feet 7⁄8 inch (2.77 m)
Height 8 feet 4 3⁄4 inches (2.56 m)
Crew 4 (Commander, Gunner, Loader/Operator, Driver)
Armour Hull front 65 millimetres (2.6 in)
sides and rear 45 millimetres (1.8 in)
Turret 65 millimetres (2.6 in) all round
Main
armament
 25 pounder tank gun, 120 rounds
Secondary
armament
 one .303 (7.7 mm) Vickers machine gun, 2,500 rounds
Engine Perrier-Cadillac
397 horsepower (296 kW)[1]
Power/weight 13.7 hp/ton
Suspension Horizontal Volute Spring
Operational
range
 200 miles (320 km)
Speed 35 miles per hour (56 km/h)

The Thunderbolt tank[2] was a cruiser tank designed and built in Australia in World War II as the successor to the AC1 Sentinel. Like the Sentinel the AC3 featured a one piece cast hull and turret. The AC3 featured a much improved design over the AC1 with better armour protection, a more power full engine, and most importantly increased firepower.

History

Even before the AC1 Sentinel began rolling off the assembly line in August 1942 it had been seen that the 2 pounder was becoming less effective as tank armour increased in thickness on new and improved enemy tanks. To address this a 25 pounder (87.6 mm, 3.45 in) gun-howitzer was fitted to a turret on the second prototype Australian cruiser tank hull and successfully test fired on 29th of June 1942.[3] With this success decided to use the 25 pounder as a tank gun. The 25 pounder redesigned as a tank gun was tested on 10th of October 1942, the work on the overhead recoil system would later prove useful for the design of the Short 25 Pounder.

Mounted in a fully traversable turret larger than that of the AC1 but using the same 54 in (1.4 m) turret ring,[4] it was slightly cramped for the turret crew but gave the AC3 both armour piercing capability as well as an effective high explosive round. The 40 volt electrical turret traverse system of the AC1 was replaced by a more powerful 110 Volt system.[5]

The hull machine gun and gunner were removed from the design to make room for stowage of the larger 25 pounder ammunition. Powered by the same three Cadillac V8 engines as the AC1, they were now mounted radially on a common crank case and geared together to form the "Perrier-Cadillac",[Note 1] a single 17.1 L, 24 cylinder engine, very similar in some respects to the later A57 Chrysler multibank used in some variants of the US M3 and M4 tanks. While the AC3 shared the same armour basis as the AC1, the hull profile had been greatly redesigned to improve the ballistic shape.

The programme was authorised to build a total of 200 Thunderbolts.[6][1] Although only one pilot model AC3 had been completed, large scale production of components had been ordered and 150 AC3 hulls cast.[7] New South Wales Government Railways' production line at Chullora work had started on assembling the first 25 AC3 tanks for trials when the programme was terminated in July 1943.[7]

Survivors

At the end of World War II all but three Australian Cruiser tanks were disposed of by the Australian government.[8][9][Note 2] The 65 tanks that were not required to serve as a physical record in war museums in Australia and the UK were sold off by the Commonwealth Disposals Commission.[8] One of the three saved was the only completed AC3 (serial number 8066) which is now located at the Treloar Technology Centre at the Australian War Memorial in Canberra.[10]

An AC3 mockup was assembled from unused AC3 armour castings and a mix of AC3 and AC1 parts at the Melbourne Tank Museum in 1996–97, this piece was sold to a private collector in 2006.[11]

Variants

See also

Tanks of comparable role, performance, and era

Notes

Footnotes
  1. ↑ Named after the French engineer Robert Perrier who was largely responsible for the design, seeMellor 1958, p. 319.
  2. ↑ Some sources state that the Sentinels were used for training after the cancellation of the program, and were not declared obsolete by the Australian Army for this purpose until 1956, see Mellor 1958, p. 308 and Bingham 1972, p. 73. However, Koudstaal 2005 states that the Sentinels were too different to the M3s and Matildas to be used for training and would require modifications and the manufacture of spares if they were to be used as special purpose vehicles. In 1945, three had been selected for preservation in war museums, while the remainder were dismantled.
Citations
  1. 1 2 3 "MP730/13, 7 A) Australian Tank Production Report by Colonel G A Green: B) Related Documents". National Archives of Australia.
  2. ↑ Beale 2011, p. 143.
  3. ↑ Bingham 1972, p. 69.
  4. ↑ "A816, 45/302/184 Australian tank production (File No.2)". National Archives of Australia.
  5. ↑ Bingham 1972, p. 73.
  6. ↑ Mellor 1958, p. 319.
  7. 1 2 3 "MP508/1, 325/703/3084 G.S. Specifications Cruiser Tank AC3 and AC4". National Archives of Australia.
  8. 1 2 "MT1274/1 325/0118/1". National Archives of Australia. Retrieved 22 June 2014. Australian "Cruiser" tanks: dismantling and disposal of 63 in total 66
  9. ↑ "No Demand For Army Tanks". Townsville Daily Bulletin. Townsville, Queensland: National Library of Australia. 2 February 1946. p. 2. Retrieved 21 June 2014.
  10. ↑ Koudstaal 2005.
  11. ↑ "The Melbourne Tank Museum Sale". Antiques Reporter. 23 June 2006. Retrieved 27 June 2016.

References

Wikimedia Commons has media related to Sentinel tank.
This article is issued from Wikipedia - version of the 8/23/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.