Springfield Model 1865

Springfield Model 1865
Type Breech-loading rifle
Place of origin United States
Service history
Used by United States
Wars Indian Wars
Production history
Designer Erskine S. Allin
Designed 1865
Manufacturer Springfield Armory
Specifications
Barrel length 33 in (840 mm) to 36 in (910 mm)
Cartridge Rimfire .58-60-500
Action Hinged, rotating breechblock, single shot
Rate of fire 8 to 10 rounds per minute

The Springfield Model 1865 was an early breech-loading rifle manufactured by U.S. Armory in Springfield, Massachusetts. It was a modification of the Springfield rifled musket Model 1861. It was later replaced with the Model 1866.

Description

During the U.S. Civil War, the advantage of breech-loading rifles became obvious. The rifled muskets used during the war had a rate of fire of 2 or 3 rounds per minute. Breech-loading rifles increased the rate of fire to 8 to 10 rounds per minute with the additional advantage that they can be easily loaded from a prone, rather than standing, position, reducing the rifleman's visible cross section and thus vulnerability to counter-fire. As the Civil War drew to a close, the U.S. Ordnance Department requested prototypes of breech-loading weapons from arms manufacturers all over the world.

After considerable testing, the prototype developed by Erskine S. Allin of the government-operated Springfield Armory was chosen for its simplicity and the fact that it could be produced by the modification of existing Springfield Model 1863 muskets. These modifications cost about $5 per rifle, which was a significant savings at a time when new rifles cost about $20 each. Patent No. 49,959 was issued to Erskine S. Allin on September 19, 1865, describing the design.

Specifications

Drawing from Erskine S. Allin's patent for the Model 1865's breech-loading system.

The conversion from musket to breechloader was done by milling open the barrel's breech section and inserting a hinged breechblock fastened to the top of the barrel. A thumb-operated cam latch at the rear of the breechblock held it shut when in closed position. The rack-type system extractor was withdrawn automatically as the breechblock was opened and snapped back at the end of its stroke. The firing pin was housed within the breechblock. The hammer nose was flattened to accommodate the firing pin.

The breech mechanism employed a hinged breechblock that rotated up and forward, resembling the movement of a trapdoor, to open the breech of the rifle and permit insertion of a cartridge. The hinged breechblock caused these rifles to be named "Trapdoor Springfields".

Approximately 5,000 Civil War Model 1861 rifled muskets were converted at the Springfield Armory in 1866. It soon became apparent that many of the small working parts in the breech system were not going to have a long service life, and the action was too complicated for normal service use. Therefore, before the Model 1865 production order was completed, a less complex rifle was already being tested. This caused the Model 1865 to be called the "First Allin", and the following revised model, the Springfield Model 1866, to be called the "Second Allin".

The Springfield model 1865 fired a rimfire .58-60-500 cartridge (.58 inch 500-grain (32 g) bullet, 60 grains (3.9 g) of black powder), the caliber matching that of the Civil War Minié ball, which was originally used in these rifles.

The Model 1865 quickly became obsolete, and most of them were sold in the 1870s to several American arms dealers. At the time, there was a large demand in the US for shorter cadet-style rifles. To satisfy this need, these dealers cut the barrels and stocks to make short rifles with 33" and 36" barrel lengths. Likewise, the stock wrists were often thinned for cadet use.

See also

References

This article is issued from Wikipedia - version of the 6/30/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.