Autonomation

Autonomation describes a feature of machine design to effect the principle of jidoka (自働化) used in the Toyota Production System (TPS) and Lean manufacturing. It may be described as "intelligent automation" or "automation with a human touch."[1] This type of automation implements some supervisory functions rather than production functions. At Toyota this usually means that if an abnormal situation arises the machine stops and the worker will stop the production line. It is a quality control process that applies the following four principles:[2]

  1. Detect the abnormality.
  2. Stop.
  3. Fix or correct the immediate condition.
  4. Investigate the root cause and install a countermeasure.

Autonomation aims to prevent the production of defective products, eliminate overproduction and focus attention on understanding the problems and ensuring that they do not reoccur.

Purpose and implementation

Autonomation is called by Shigeo Shingo pre-automation.[3] It separates workers from machines through mechanisms that detect production abnormalities (many machines in Toyota have these). He says there are twenty-three stages between purely manual and fully automated work. To be fully automated machines must be able to detect and correct their own operating problems which is currently not cost-effective. However, ninety percent of the benefits of full automation can be gained by autonomation.

The purpose of autonomation is that it makes possible the rapid or immediate address, identification and correction of mistakes that occur in a process. Autonomation relieves the worker of the need to continuously judge whether the operation of the machine is normal; their efforts are now only engaged when there is a problem alerted by the machine. As well as making the work more interesting this is a necessary step if the worker is to be asked later to supervise several machines. The first example of this at Toyota was the auto-activated loom of Sakichi Toyoda that automatically and immediately stopped the loom if the vertical or lateral threads broke or ran out.

For instance rather than waiting until the end of a production line to inspect a finished product, autonomation may be employed at early steps in the process to reduce the amount of work that is added to a defective product. A worker who is self-inspecting their own work, or source-inspecting the work produced immediately before their work station is encouraged to stop the line when a defect is found. This detection is the first step in Jidoka. A machine performing the same defect detection process is engaged in autonomation.

Once the line is stopped a supervisor or person designated to help correct problems gives immediate attention to the problem the worker or machine has discovered. To complete Jidoka, not only is the defect corrected in the product where discovered, but the process is evaluated and changed to remove the possibility of making the same mistake again. One solution to the problems can be to insert a "mistake-proofing" device somewhere in the production line. Such a device is known as poka-yoke.

Relationship with Just-in-Time

Taiichi Ohno and Sakichi Toyoda, originators of the TPS and practices in the manufacturing of textiles, machinery and automobiles considered JIT & Autonomation the pillars[4] upon which TPS is built. Jeffrey Liker and David Meier[5] indicate that Jidoka or "the decision to stop and fix problems as they occur rather than pushing them down the line to be resolved later" is a large part of the difference between the effectiveness of Toyota and other companies who have tried to adopt Lean Manufacturing. Autonomation, therefore can be said to be a key element in successful Lean Manufacturing implementations.

For Just-in-Time (JIT) systems, it is absolutely vital to produce with zero defects, or else these defects can disrupt the production process - or the orderly flow of work.

JIT and Lean Manufacturing are always searching for targets for continuous improvement in its quest for quality improvements, finding and eliminating the causes of problems so they do not continually crop up.

Jidoka involves the automatic detection of errors or defects during production. When a defect is detected the halting of the production forces immediate attention to the problem.

The halting causes slowed production but it is believed that this helps to detect a problem earlier and avoids the spread of bad practices. (JBLL, Jun18, 2006)

Etymology

The word "autonomation" 自働化, a loan word from the Sino-Japanese vocabulary, is a portmanteau of "autonomous" and "automation" 自動化, which is written using three kanji characters: 自 "self", "動" "movement", and 化 "-ization". In the Toyota Production System, the second character is replaced with 働 "work", which is a character derived by adding a radical representing "human" to the original 動.

References

  1. ↑ Toyota Production System, Taiichi Ohno, Productivity Press, 1988, page 6.
  2. ↑ The Essence of Jidoka, Mark Rosenthal, SME Lean Directions Newsletter, 2002
  3. ↑ Toyota Production System, Taiichi Ohno, Productivity Press, 1988, p 58
  4. ↑ Toyota Production System, Taiichi Ohno, Productivity Press, 1988, p 4
  5. ↑ the first paragraph of Chapter 8 in their book, The Toyota Way Fieldbook, Jeffrey Liker and David Meier

See also

Related concepts from the Toyota Production System:

This article is issued from Wikipedia - version of the 10/22/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.