2014 aluminium alloy
2014 aluminium alloy is an aluminium-based alloy often used in the aerospace industry.[1]
It is easily machined in certain tempers, and among the strongest available aluminium alloys, as well as having high hardness. However, it is difficult to weld, as it is subject to cracking.[2]
2014 is the second most popular of the 2000-series aluminum alloys, after 2024 aluminum alloy. It is commonly extruded and forged. The corrosion resistance of this alloy is particularly poor. To combat this, it is often clad with pure aluminum. If unclad 2014 aluminum is to be exposed to the elements, it should be painted as a corrosion protection measure.[3]
Prior to the adoption of The Aluminum Association alloy designations in 1954, 2014 was known by the industry conventional designation "14S".[4]
Chemical Composition
The alloy composition of 2014 is:[2]
- Aluminum: Remainder
- Chromium: 0.1% max
- Copper: 3.9% - 5%
- Iron: 0.7% max
- Magnesium: 0.2% - 0.8%
- Manganese: 0.4 - 1.2%
- Remainder: Each 0.05% max
- Remainder: Total 0.15% max
- Silicon: 0.5% - 1.2%
- Titanium: 0.15% max
- Titanium + Zinc: 0.2% max
- Zinc: 0.25% max
2014A Aluminum Alloy
2014A is an alloy of aluminum that is very similar (but not entirely identical) to 2014. Because of the naming similarity, the two can be confused. The alloy composition of 2014A is:[1]
- Aluminum: Remainder
- Chromium: 0.1% max
- Copper: 3.9% - 5%
- Iron: 0.5% max (versus 0.7 for 2014)
- Magnesium: 0.2% - 0.8%
- Manganese: 0.4 - 1.2%
- Remainder: Each 0.05% max
- Remainder: Total 0.15% max
- Silicon: 0.5% - 0.9% (versus 0.5-1.2 for 2014)
- Titanium: 0.15% max
- Titanium + Zinc: 0.2% max
- Zinc: 0.25% max
Properties
Typical material properties for 2014 aluminum alloy are:[5]
- Density: 2.80 g/cm3, or 175 lb/ft3.
- Young's modulus: 73 GPa, or 11 Msi.
- Electrical conductivity: 34 to 50% IACS.
- Ultimate tensile strength: 190 to 480 MPa, or 28 to 70 ksi.
- Thermal Conductivity: 130 to 190 W/m-K.
- Thermal Expansion: 23 μm/m-K.
Standards
2014 aluminum alloy is discussed in the following standards:[5]
- ASTM B 209: Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
- ASTM B 210: Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes
- ASTM B 211: Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire
- ASTM B 221: Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
References
- 1 2 Datasheets - Aluminium Alloy - BS-L - L168 T6511 - 2014A Bar | Wilsons Ltd
- 1 2 http://www.suppliersonline.com/propertypages/2014.asp
- ↑ Marks' Standard handbook for Mechanical Engineers, 8th Ed., McGraw Hill, pp. 6-50 to 6-56
- ↑ Oberg, Erik; et al. (2004). Machinery's Handbook (27th ed.). Industrial Press Inc. p. 578. ISBN 0-8311-2700-7.
- 1 2 2014 (3.1255, H15, A92014) Aluminum. Retrieved on 2014-12-01.
Further reading
- "Properties of Wrought Aluminum and Aluminum Alloys: 2014, Alclad 2014". Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, Vol 2, ASM Handbook, ASM International, 1990, p. 67-68.